RECOMMENDED
ADDITIONAL ITEMS
Safety Glasses
Paper Towel
Sink & Hot Water
Soap / Detergent
Cleaning Solvent
(eg Isopropyl Alcohol)
Resin
(see website for details) *
Photocentric Resin Cleaner *
Photocentric Wash 15 *
Photocentric Cure M *
Liquid Crystal Dental
Vat Film and Gasket Pack *
Liquid Crystal
Dental Resin Vat *
Liquid Crystal
Dental Print Platform *
* Available from Photocentric
Read this Liquid Crystal Dental User Manual
carefully and retain it for future reference.
- Take note of all warnings displayed on the 3D
printer.
- Follow all instructions displayed on the 3D
printer.
- Liquid Crystal Dental weighs 40 kg. At least
two people are required to lift it safely.
- Operate the 3D printer on a flat and stable
surface that can safely support the weight.
- Position the 3D printer at a height that allows a
comfortable posture during operation.
- Keep the 3D printer and photopolymer resin
out of the reach of children.
- Liquid Crystal Dental requires a mains power
supply with a voltage of 100 VAC - 240 VAC
and a frequency of 50 Hz - 60 Hz.
- Liquid Crystal Dental has a maximum power
consumption of 700 W. It will draw a maximum
current of 3.0 A when connected to a 240 VAC
supply, or 7.0 A when connected to a 100 VAC
supply.
- Only connect Liquid Crystal Dental to the
mains socket using the power cable supplied.
- Ensure that the total current draw of all items
connected to the mains circuit does not exceed
the capacity of the fuse or circuit breaker.
- Always plug the power cable into the mains
socket and the 3D printer before switching on
the power at the mains socket.
- Always switch off the power at the mains socket
before unplugging the power cable from either
the 3D printer or the mains socket.
- Do not place anything on top of, or resting
against, the power cable.
- Do not position the power cable such that it
causes a trip hazard, or is likely to be stepped
on.
- Disconnect the 3D printer from the mains
socket when not in use.
- Do not operate Liquid Crystal Dental outdoors.
- Liquid Crystal Dental should not be operated in
direct light from the sun or any UV light source.
- Liquid Crystal Dental should be operated in an
ambient temperature of 15 °C - 25 °C.
- Liquid Crystal Dental should be operated in a
well ventilated room.
- Do not operate Liquid Crystal Dental with the
hood open as you may be exposed to crush
hazards, harmful UV light or other hazards.
- Photopolymer resin is an irritant. Always wear
gloves and safety glasses when handling
photopolymer resin.
- Do not operate Liquid Crystal Dental if you
display signs of sensitivity after exposure
to photopolymer resin, such as skin or eye
irritation.
- Do not allow photopolymer resin or any other
liquid to get inside the casing of the 3D printer.
Clean up any spills immediately.
- In case of malfunction, switch off the power at
the mains socket and disconnect the 3D printer
immediately.
- Do not disassemble Liquid Crystal Dental as
you may be exposed to electric shock hazards,
harmful UV light or other hazards.
- All repairs should be carried out by trained
service personnel.
- Discontinue 3D printer operation and contact
your supplier if:
o The power cable or plug is damaged.
o Liquid has got inside the casing of the 3D
printer.
o The 3D printer has been dropped.
o The 3D printer shows signs of damage.
o The 3D printer does not operate correctly
after following the instructions provided in this
user manual.
- Dispose of waste photopolymer resin
responsibly. Do not put photopolymer resin
down the drain. Resin can be cured using
any UV light source. Fully cured resin can be
disposed of with normal waste.
- Dispose of Liquid Crystal Dental responsibly.
Please recycle where possible or return to
Photocentric for recycling.
3. SAFETY
INFORMATION
3
4
DENTAL
Liquid Crystal
DENTAL
Liquid Crystal
5mm Allen Key
Funnel
Spray Bottle
Power Cable
Soft Spatula
5x Paper
Resin Filters
PZ2 Screwdriver
PZ1 Screwdriver
2x Gloves
2x Vat Gaskets
2x Vat Film
Vat Cleaning Tool
Wi-FI Dongle
3mm Allen Key
1kg Sample Resin
Scraper
Platform
Hanger
16 GB USB Flash Drive
Liquid Crystal Dental User Manual
Photocentric Studio Licence Number
Resin Material Safety Data Sheet
CE Certificate
Resin Vat
Print Platform
4. BOX CONTENTS
DENTAL
Liquid Crystal
Silicone Mat
