Question
Answer
Why does the parent
unit beep?
If the parent unit beeps while the LINK light lights up red continuously
and the message ‘Not Linked’ is shown on the display, the connection
with the baby unit is lost. Move the parent unit closer to the baby unit.
If the parent unit beeps and the battery symbol on the display is
empty, the rechargeable battery pack of the parent unit is running low.
Recharge the rechargeable battery pack.
If you have switched off the volume while the sound alert is on, the
parent unit beeps whenever the fourth sound level light lights
up because the baby unit has picked up a sound.
If you have set the room temperature range on the parent unit and
the temperature alert is on, the parent unit beeps when the
temperature drops below the set level or below 57°F (14°C) or
when the temperature rises above the set level or above 86°F (30°C).
The baby unit may be switched off. Switch on the baby unit.
Why does the appliance
produce a high-pitched
noise?
The units may be too close to each other. Make sure the parent unit
and the baby unit are at least 3 feet/1 meter away from each other.
The volume of the parent unit may be set too high. Decrease the
volume of the parent unit.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The volume of the parent unit may be set too low or may be
switched off. Increase the volume of the parent unit.
The microphone sensitivity level of the baby unit may be set too low.
Set the microphone sensitivity level to a higher level in the menu of
the parent unit.
The baby unit and the parent unit may be out of range of each other.
Reduce the distance between the units.
Why does the parent
unit react too quickly to
other sounds?
The baby unit also picks up other sounds than those of your
baby. Move the baby unit closer to the baby (but observe the
minimum distance of 3 feet/1 meter).
The microphone sensitivity level of the baby unit may be set too high.
Decrease the microphone sensitivity level in the menu of the parent
unit.
Why does the parent
unit react slowly to the
baby’s crying?
The microphone sensitivity level of the baby unit may be set too low.
Increase the microphone sensitivity level of in the menu of the parent
unit.
Why do the non-
rechargeable batteries of
the baby unit run low
quickly?
The microphone sensitivity level of the baby unit may be set too high,
which causes the baby unit to transmit more often. Decrease the
microphone sensitivity level in the menu of the parent unit.
The volume on the baby unit may be set too high, which causes the
baby unit to consume a lot of energy. Decrease the volume of the
baby unit.
EngliSh
22
Question
Answer
You may have set a maximum room temperature that is lower than
the actual room temperature or a minimum room temperature that is
higher than the actual room temperature. In this case the display is lit
all the time, which increases the power consumption of the baby unit.
This causes the non-rechargeable batteries of the baby unit to run
low quickly.
Perhaps you have switched on the nightlight. If you want to use the
nightlight, we advise you to run the baby unit on outlet electricity.
Why does the charging
time of the parent unit
exceed 4 hours?
The parent unit may be switched on during charging. Switch off the
parent unit during charging.
The specified operating
range of the baby
monitor is 1000 feet/330
meters. Why does my
baby monitor manage a
much smaller distance
than that?
The specified range is only valid outdoors in open air. Inside your
house, the operating range is limited by the number and type of walls
and/or ceilings in between. Inside the house, the operating range is up
to 150 feet/50 meters.
Why is the
connection lost every
now and then? Why are
there sound
interruptions?
The baby unit and the parent unit are probably close to the outer
limits of the operating range. Try a different location or decrease the
distance between the units. Please note that it takes about 30 seconds
each time before a connection between the units is established.
What happens during a
power failure?
If the parent unit is sufficiently charged, it continues to operate during
a power failure, both inside and outside the charger. If there are
batteries in the baby unit, it also continues to operate during a power
failure.
Is my baby monitor
secure from
eavesdropping and
interference?
The DECT technology of this baby monitor guarantees no
interference from other equipment and no eavesdropping.
The operating time of
the parent unit is
supposed to be at
least 24 hours. Why is
the operating time of my
parent unit shorter?
When the rechargeable battery pack of the parent unit has been
charged for the first time, the operating time is less than 24 hours. The
rechargeable battery pack only reaches its full capacity after you have
charged and discharged it at least four times.
The volume of the parent unit may be set too high, which causes the
parent unit to consume a lot of energy. Decrease the volume of the
parent unit
The microphone sensitivity level of the baby unit may be set too high,
which causes the parent unit to consume a lot of energy. Decrease
the microphone sensitivity level in the menu of the parent unit.
EngliSh
2
