Philips FW350C, Руководство пользователя

Страница: 22 / 22

22
English
3139 116 19271
Warning! Under no circumstances
you should try to repair the set yourself
as this will invalidate the guarantee.
Do not open the set as there is a risk of
electric shock.
• If a fault occurs, check the points listed
below before taking the system for
repair.
• Should any problems persist after you
have made these checks, consult your
nearest dealer or service center.
CD Player Operation
“
NO DISC
” is displayed.
• The disc is inserted upside down.
™ Place CD with printed side up.
• Moisture condensation at the lens.
™ Wait until lens has adjusted to normal
room temperature.
• There is no disc in the CD tray.
™ Insert a CD.
• The CD is dirty, badly scratched or
warped.
™ Clean or replace the CD.
• The CD lens is dirty or dusty
™ See section under Maintenance.
“
DISC NOT FINALIZED
” is
displayed.
• The CD-RW or CD-R disc is not properly
recorded for the use of a standard CD
player.
™ Read the instruction booklet of your CD-
Rewritable or CD-Recorder on how to
finalize a recording.
• The CD is badly scratched or dirty.
™ Replace or clean CD.
Radio Reception
Poor radio reception
• The signal strength is too weak.
™ Adjust the antenna.
• The TV or VCR is too close to the stereo
system.
™ Separate the stereo system from the TV
or VCR.
™ Connect an external antenna for better
reception.
Tape Deck Operation
“
RECORDING ACTIVE
” is displayed.
• A recording is in progress.
™ Stop the recording or wait until it is
finished.
“
TAPE DUBBING ONLY
” is
displayed.
• Tape dubbing is only possible in tape
mode.
™ Switch source to tape mode.
Recording or playback cannot be
made or there is a decrease in audio
level.
• Dirty tape heads, capstans or pressure
rollers.
™ See section on tape deck maintenance.
• Magnetic build-up in the record/
playback head.
™ Use demagnetizing tape.
Remote control has no effect on the
system.
• The distance to the system is too large.
™ Reduce the distance.
• Batteries are inserted incorrectly.
™ Insert the batteries with their polarities
(+/– signs) as indicated..
• Batteries are exhausted.
™
Replace the batteries.
• Wrong source is selected.
™ Select the source (CD, TUNER, etc.)
before pressing the function button,
(PLAY, PREV/NEXT, etc.).
Timer not working.
• Timer is not switched on.
™ Press CLOCK/TIMER to switch on the
timer.
• Dubbing/recording is in progress.
™ Stop dubbing/recording.
System displays features
automatically; buttons flash
continuously.
• Demonstration mode is switched on.
™ Press and hold
Ç
for 5 seconds to
switch off the demonstration.
TROUBLESHOOTING
General
System does not react when any
button is pressed.
• Electrostatic discharge.
™ Press STANDBY-ON to switch the
system off. Remove the AC power plug
from the wall outlet, then reconnect
and switch on the system again.
No or poor sound.
• Volume is not turned up.
™ Adjust VOLUME.
• The system is muted.
™ Press MUTE to switch on the sound.
• The headphones are connected.
™ Disconnect the headphones.
• Speakers are not connected or are
connected wrongly.
™
Check that the speakers are connected
correctly.
™ Make sure that the stripped speaker
wire is clamped.
Reversed left and right sound.
• Speakers are connected wrongly.
™ Check the speaker connections and
location.
Lack of bass sound or apparently
imprecise physical location of musical
instruments.
• Speakers are connected wrongly.
™ Check the speaker connection for
proper phasing, red/black wires to red/
black terminals.
Untitled-1 6/15/00, 2:05 PM 22