Philips DVD755VR Скачать руководство пользователя | Manualshive

Страница: 122 / 154

background image

MAINTENANCE/INSPECTION PROCEDURE

4-20

2. Required Maintenance

The recording density of a VCR(VCP) is much higher than
that of an audio tape recorder. VCR(VCP) components must
be very precise, at tolerances of 1/1000mm, to ensure com-
patibility with the other VCRs. If any of these components are
worn or dirty, the symptoms will be the same as if the part is
defective. To ensure a good picture, periodic inspection and
maintenance, including replacement of worn out parts and
lubrication, is necessary.

3. Scheduled Maintenance

Schedules for maintenance and inspection are not fixed
because they vary greatly according to the way in which the
customer uses the VCR(VCP), and the environment in which
the VCR(VCP) is used.
But, in general home use, a good picture will be maintained
if inspection and maintenance is made every 1,000 hours.
The table below shows the relation between time used and
inspection period.

Table 1

4. Supplies Required for Inspection and

Maintence

(1) Grease : Kanto G-311G (Blue) or equivalent
(2) Isopropyl Alcohol or equivalent
(3) Cleaning Patches
(4) Grease : Kanto G-381(Yellow)

5. Maintenance Procedure

5-1) Cleaning

(1) Cleaning video head

First use a cleaning tape. If the dirt on the head is too
stubborn to remove by tape, use the cleaning patch. Coat
the cleaning patch with Isopropyl Alcohol. Touch the
cleaning patch to the head tip and gently turn the
head(rotating cylinder) right and left.
(Do not move the cleaning patch vertically. Make sure
that only the buckskin on the cleaning patch comes into
contact with the head. Otherwise, the head may be dam-
aged.)
Thoroughly dry the head. Then run the test tape. If lso-
propyl Alcohol remains on the video head, the tape may
be damaged when it comes into contact with the head
surface.

(2) Clean the tape transport system and drive system, etc, by

wiping with a cleaning patch wetted with Isopropyl
Alcohol.

NOTES:

1

It is the tape transport system which comes into contact
with the running tape. The drive system consists of those
parts which moves the tape.

2

Make sure that during cleaning you do not touch the tape
transport system with excessive force that would cause
deformation or damage to the system.

About 1

year

One hour

Two hours

Three hours

When

inspection is

necessary

Average

hours used

per day

About 18

months

About 3

years

Fig. C-9-4

Drum
(Rotating Cylinder)

Head Tip

Coat With Isopropyl Alcohol

Touch this section of cleaning
patch to the head tip and gently
turn the Drum (Rotating Cylinder)

Cleaning Patch

«
...
120
121
122
123
124
...
»

Содержание DVD755VR



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DVD755VR

26MD357B - LCD HDTV With DVD Player

Бренд: Magnavox Страницы: 3

23/51E-BB-FTCDUP-UK

Бренд: UMC Страницы: 32

Бренд: Technika Страницы: 29

Бренд: Technika Страницы: 32

Бренд: Technika Страницы: 30

Бренд: AWA Страницы: 26

Бренд: Samsung Страницы: 79

Бренд: Toshiba Страницы: 105

Бренд: Haier Страницы: 42

Бренд: Supersonic Страницы: 1

Бренд: Sylvania Страницы: 28

Бренд: Sylvania Страницы: 42

Бренд: Sylvania Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды