Philips DVD755VR Скачать руководство пользователя | Manualshive

Страница: 116 / 154

background image

4-14

DECK MECHANISM ADJUSTMENT

Purpose: To insure smooth transport of the tape during each mode of operation.

If the tape transport is abnormal, then check the torque as indicated by the chart below.

2. Preparation for Adjustment (To set the

Deck Mechanism of the loading state
without inserting a cassette tape).

1) Unplug the power cord from the AC outlet.
2) Disassemble the Top Cover and Plate Assembly Top.
3) Plug the power cord into the AC outlet.
4) Turn the power S/W on and push the Lever Stopper of

the Holder Assembly CST to the back for loading the

cassette without tape.
Cover the holes of the End Sensors at the both sides of
the Chassis to prevent a light leak.
Then the Deck Mechanism drives to the Stop Mode.
In this case, the Deck Mechanism can accept inputs of
each mode, however the Rewind and Review operation
can not be performed for more than a few seconds
because the Take-up Reel Table is in the Stop State
and can not be detected the Reel Pulses.

3. Checking Torque

NOTE:

The values are measured by using a Torque Gauge and
Torque Gauge Adaptor with the Torque Gauge affixed.

NOTE:

The torque reading to measure occurs when the tape
abruptly changes direction from Fast Forward to Rewind
Mode, when quick braking is applied to both Reels.

SRK

VIDEO

CASSETTE

TORQUE

METER

VHT-303

S

R

K

-

V

H T

- S

SR

K - V H T - T

300

250

200

150

50

0

300

250

200

150

50

0

100

Test Equipment/ Fixture

• Torque Gauge(600g/cm ATG)
• Torque Gauge Adaptor
• Cassette Torque Meter

SRK-VHT-303

Checking Method

• Perform each Deck Mechanism mode without

inserting a cassette tape(Refer to above No.2
Preparation for Adjustment).

• Read the measurement of the Take-up or Supply

Reels on the Cassette Torque Meter(Fig. C-3-2).

• Attach the Torque Gauge Adaptor to the Torque

Gauge and then read the value of it(Fig. C-3-1).

Fig. C-3-2

Fig. C-3-1

Torque Gauge

Torque Gauge
Adaptor

Reel Table

Item

Fast Forward Torque

Rewind Torque

Play Take-Up Torque

Review Torque

Mode

Fast Forward

Rewind

Play

Review

Test Equipment

Cassette Torque Gauge

Cassette Torque Gauge

Cassette Torque Meter

Cassette Torque Meter

Measurement Reel

Take-Up Reel

Supply Reel

Take-Up Reel

Supply Reel

Measurement Values

More than 400g/cm

More than 400g/cm

40~100g/cm

120~210g/cm

Test Conditions

(Mechanism Condition)

• Play (FF) or Review (REW) Mode

• Cassette Torque Meter (SRK-VHT-303)

• Torque Gauge (600g.cm ATG)

«
...
114
115
116
117
118
...
»

Содержание DVD755VR



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DVD755VR

Бренд: Sylvania Страницы: 40

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 29

Бренд: Toshiba Страницы: 44

Бренд: Toshiba Страницы: 38

Бренд: Toshiba Страницы: 56

Бренд: Toshiba Страницы: 60

Бренд: Toshiba Страницы: 56

Бренд: Toshiba Страницы: 56

Бренд: Toshiba Страницы: 64

Бренд: Toshiba Страницы: 50

Бренд: Toshiba Страницы: 63

Бренд: Toshiba Страницы: 55

Бренд: Toshiba Страницы: 60

Бренд: Toshiba Страницы: 58

Бренд: Toshiba Страницы: 56

Бренд: Toshiba Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды