Philips DVD755VR Скачать руководство пользователя

Страница: 118 / 154

4-16

DECK MECHANISM ADJUSTMENT

5. Audio/Control (A/C) Head Adjustment

10.9

Purpose: To insure that the tape passes accurately over the Audio and Control Tracks in

exact alignment of the both Record and Playback Modes.

Test Equipment/ Fixture

• Blank Tape
• Screw ) Type 5mm

• Play the blank tape

Test Conditions (Mechanism Condition)

Adjustment Point

• Tilt Adjustment Screw(C)
• Height Adjustment Screw(B)
• Azimuth Adjustment Screw(A)

Fig. C-5-1

A/C Head Base

Fig. C-5-2

Height Adjustment

Screw(B)

Tilt Adjustment

Screw(C)

Azimuth Adjustment
Screw(A)

X-Value Adjustment
Hole

Fixed Screw

Fig. C-5-3

A/C Head

Tape

0.2~0.25mm

5-1. Preliminary Adjustment (Height and Tilt Adjustment)

Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape.

1) Initially adjust the Base Assembly A/C Head as shown

Fig. C-5-1 by using the Height Adjustment Screw(B).

2) Play a blank tape and observe if the tape passes accu-

rately over the A/C Head without tape curling or folding.

3) If folding or curling is occured then adjust the Tilt

Adjustment Screw(C) while the tape is running to resem-
ble Fig. C-5-3.

4) Reconfirm the tape path after Playback about 4~5 sec-

onds.

NOTE

Ideal A/C head height occurs when the tape runs between
0.2~0.25mm above the bottom edge of the A/C Head core.

Adjustment Procedure/Diagrams

A/C Head Assembly

Содержание DVD755VR



























































































































































Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды

Philips DVD755VR, Руководство по обслуживанию

Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды