Philips AZ 3038, Руководство по обслуживанию, Страница: 8 / 25

3 - 4
Erasing a programme You can erase the contents of the memory by: – opening the CD door; – selecting
TUNER
source;
– pressing
9
(twice during playback or in the stop
position).
Display: shows
briefly when
programme is cancelled. (See
@
)
Precautions & General Maintenance
(See
#
)
•
Place the set on a hard and flat surface so that the system does not tilt.
•
Do not expose the set, batteries or CDs to humidity
, rain, sand or excessive heat caused by
heating equipment or direct sunlight.
•
Do not cover the set. Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up.
•
The mechanical parts of the set contain self- lubricating bearings and must not be oiled or lubricated.
•T
o clean the set, use a soft dry cloth. Do not use
any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing.
CD player and CD handling
(See
$
)
•
The lens of the CD player should never be touched!
•
Sudden changes in the surrounding temperature can cause condensation to form and the lens of your CD player to cloud over
. Playing a CD is then
not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates.
•
Always close the CD door to keep the CD compartment dust-free. T
o clean, dust the
compartment with a soft dry cloth.
•T
o clean the CD, wipe in a straight line from the
centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc.
•
Never write on a CD or attach any stickers to it.
–
Problem
•
Solution
No sound /power –V
olume not adjusted
•
Adjust the VOLUME
–
Power cord not securely connected
•
Connect the AC power cord properly
–
Batteries dead/ incorrectly inserted
•
Insert (fresh) batteries correctly
Display does not function does not function properly/ No reaction to operation of any of the controls –
Electrostatic discharge
•
Switch off and unplug the set. Reconnect after a few seconds
or indication
MP3-CD/ CD playback does not work –
No disc inserted
•
Insert a disc
–
Disc badly scratched or dirty
•
Replace/ clean disc (see Maintenance)
–
Laser lens steamed up
•W
ait until lens has recovered to room temperature
–
CD-R(W) is blank or the disc is not finalized
•
Use a finalized CD-R(W)
–
Incompatible format used for MP3
•
Check if your disc format is ISO 9960, Joliet, finalized multisession
–
Not all known encrypted and protected CDs are compatible
•
Make sure to deactivate the protection option in the encoder software before creating the music files
The disc skips tracks –
Disc damaged or dirty
•
Replace or clean disc
–
Shuffle or a programme is active
•
Quit shuffle/ programme mode(s)
Sound skips during MP3 playback –
MP3 file made at compression level exceeding 320kbps
•
Use a lower compression level to record CD tracks into MP3 format
Cannot find desired MP3 title –
Wrong file extension/ used
•
Change file extension to .MP3
Troubleshooting If a fault occurs, first check the points listed below before taking the set for repair
.
Do not open the set as there is a risk of electric shock. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
W
ARNING:
Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee.
MP3-CD/ CD PLA
YER
MAINTENANCE
TROUBLESHOOTING
Environmental information All unnecessary packing material has been omitted. The packing can be easily separated into three materials: cardboard, polystyrene and plastic. Your set consists of materials which can be recycled if disassembled by a specialized company
. Please observe
the local regulations regarding the disposal of packing materials, dead batteries and old equipment.
For more detail on operation instruction please visit Philips Audio internet site :
http://www.audio.philips.com
INSTRUCTIONS FOR USE