Philips AZ 3038, Руководство по обслуживанию, Страница: 6 / 25

3 - 2
English
CONTROLS
POWER SUPPL
Y
Using AC Power 1
Check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local power supply
. If it does not, consult
your dealer or service centre.
2
Connect the power cord to the AC MAINS inlet and the wall outlet. The power supply is now connected and ready for use.
3
To
switch off completely
, unplug the power cord
from the wall outlet.
•
Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.
The typeplate is located on the bottom of the set. Switching power on/off: Save energy Whether you are using mains or battery supply
, to
avoid unnecessary energy consumption always adjust the source selector to off. General operation 1
To
select your sound source adjust the source
selector to
CD/TUNER/OFF
.
2
Adjust the sound with the
VOLUME
and
DBB
(Dynamic Bass Boost) controls.
3
To
switch off the set, adjust the source selector to
off position.
Note: When the set is switched off the tuner presets will be retained in the set’
s memory
.
Radio reception 1
Adjust the source selector to
TUNER
.
™
Display: shows
briefly
.
2
Press FM•MW once or more to select the desired waveband. ™
Display: shows your waveband and the preset number and the frequency of a preset station if already programmed (See
4
).
3
Press and hold down
or
§
§
§
briefly to tune to a
radio station. Release when the frequency in the display starts to change. ™
The radio automatically tunes to a radio station of sufficient reception. Display shows during automatic tuning.
–
If you want to stop automatic tuning, press
or
§
briefly
.
–
For
FM
, pull out the telescopic aerial. Incline and
turn the aerial. Reduce its length if the signal is too strong (very close to a transmitter).
–
For
MW (AM)
the set is provided with a built-in
aerial so the telescopic aerial is not needed. Direct the aerial by turning the whole set.
Programming radio stations You can store up to a total of 32 radio stations in the memory
.
1
Tune to your desired station (see Radio Reception).
2
Press
PROG•MODE
to activate programming.
™
Display: flashes.
3
Press
PRESET•TRACK –, +10
once or more to
allocate a number from 1 to 32 to this station.
4
Press
PROG•MODE
again to confirm the setting.
™
Display: disappears,
the
preset
number
and the frequency of the preset station are shown.
5
Repeat steps 1-4 to store other stations.
•Y
ou can erase a preset station by storing another
frequency in its place.
Top and front panels (See
1
)
1
VOLUME – adjusts volume level
2
DBB
(Dynamic Bass Boost)
– enhances bass response
3
Source selector – selects source of sound
CD
or
TUNER
. Also the
power off switch
4
PRESS
TO
PLA
Y
2;
– starts or pauses MP3-CD/ CD playback
5
STOP
9
– stops MP3-CD/ CD playback; erases a MP3-CD/ CD programme
6
LIFT TO OPEN – opens/ closes the CD door
7
Display – shows the CD player and tuner functions
8
PROG•MODE MP3-CD: –
programmes
and
reviews
programmed
track numbers; – plays tracks MP3-CD/ CD/ programme in random order; – repeats a track/ MP3-CD/CD / programme
Tuner: –
programmes
tuner
preset
stations
9
FM•MW – selects FM/ MW (AM) waveband
0
PRESET•TRACK –, +10 MP3-CD:
fast skips to the next/ previous 10 MP3-CD tracks
Tuner:
selects a preset station (down, up)
!
SEARCH
,
§§
MP3-CD: skips
or
searches
a
passage/track
backwards or forward
Tuner:
tunes to a station (up, down)
@
IR sensor – infrared for remote control
Back Panel (See
1
)
#
Telescopic aerial – to improve FM reception
$
Battery door – to open battery compartment
%
AC MAINS – inlet for mains lead
Remote Control 1
¡
,
™
– skips to the next/ previous track
2
2;
– to start or interrupt MP3-CD/CD playback
3
9
– to stop playback; to erase a programme
Power Supply Whenever convenient, use the power supply if you want to conserve battery life. Make sure you remove the plug from the set and wall outlet before inserting batteries. For users in the U.K.: please follow the instructions in the box, Important notes for users in the U.K. Batteries (not included) (see
2
)
Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "–" symbols inside the compartment. Remote control (see
3
)
Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline). Batteries contain chemical substances, so they should be disposed of properly
.
Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: •
Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.
•
When inserting new batteries, do not try to mix old batteries with the new ones.
•
Remove the batteries if the set is not to be used for a long time.
GENERAL OPERA
TION
DIGIT
AL TUNER
CONNECTIONS AND CONTROLS