Philips 50 T Series страница 24 Скачать руководство пользователя

Страница: 24 / 105

Error Messages

Chapter 3 - Tests and Error Messages

Error Messages

The following error messages are directly related to telemetry and appear on
the fetal monitor. Refer to the Instructions for Use provided with your monitor
for error messages not related to telemetry monitoring.

Series 50 Family

8040A

Message

Display

Cause

Solution

Err 9

US Toco

Invalid telemetry mode.

Check the cable from the telemetry
receiver and, if necessary, replace it.

Err 14

US Toco

Incorrect transducer
connected to transmitter.

Check that the transducer is
compatible with Series 50T Fetal
Telemetry System.

Err 16

US Toco

Transducers are
connected to the front
panel of the monitor.

Disconnect the transducers from
the monitor or switch off the
telemetry receiver.

Message

Display

Cause

Solution

Err 16

US Toco

Transducers are
connected to the front
panel of the monitor.

Disconnect the transducers from the monitor or
switch off the telemetry receiver.

*. No longer available.

Содержание 50 T Series










































































































Результаты поиска

Содержание 50 T Series

Отзывы:

Похожие инструкции для 50 T Series

Бренды по названию

Популярные бренды

Philips 50 T Series, Руководство по обслуживанию

Результаты поиска

Содержание 50 T Series

Отзывы:

Похожие инструкции для 50 T Series

Бренды по названию

Популярные бренды