Philips 50 T Series страница 17 Скачать руководство пользователя

Страница: 17 / 105

Telemetry System (Receiver and Transmitter)

Chapter 2 - Technical Specifications

Transmitter

•

Cardio socket for M1356A ultrasound transducer or the M1357A/
M1364A DECG transducer.

•

Toco socket for the M1355A Toco transducer or an IUP Transducer
(CPJ840J5).

•

Remote Event Marker and Service Socket.

Outputs

Receiver

•

25 pin RS232 Socket for connecting the Fetal Monitor.

Input Sensitivity

-118dBM

Output Power

Transmitter

4 mW (USA)

2 mW (Europe)

1 mW (Japan)

Image Rejection

>80 dB

Self-Test Facilities

Self-test facilities include:

•

Receiver Self Test: Tests the Receiver LF Part.

•

Transmitter Self Test: Tests the Transmitter LF Part.

•

Parameter Test: With the appropriate transducer connected to the
Transmitter, the monitoring mode (ultrasound/DECG or Toco/IUP) is
tested from the Transmitter via Receiver to the connected Fetal
Monitor.

Содержание 50 T Series










































































































Результаты поиска

Содержание 50 T Series

Отзывы:

Похожие инструкции для 50 T Series

Бренды по названию

Популярные бренды

Philips 50 T Series, Руководство по обслуживанию

Результаты поиска

Содержание 50 T Series

Отзывы:

Похожие инструкции для 50 T Series

Бренды по названию

Популярные бренды