Philips 50 T Series страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 105

background image

Notice

Philips makes no warranty of any kind with regard to this material, including,
but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Philips shall not be liable for errors contained herein or
for incidental or consequential damages in connection with the furnishing,
performance or use of this material.

The information contained in this document is subject to change without
notice.

Philips assumes no responsibility for the use or reliability of its software on
equipment that is not furnished by Philips.

Responsibility of the Manufacturer

Philips only considers itself responsible for any effects on safety, reliability and
performance of the equipment if:

• assembly operations, extensions, re-adjustments, modifications or repairs

are carried out by persons authorized by Philips, and

• the electrical installation of the relevant room complies with national

standards, and

• the instrument is used in accordance with the Instructions for Use or User’s

Guide.

Important

United States federal law restricts this device to sale by or on the order of a
physician.

This device is not intended for home use.

Warning
Failure on the part of the responsible individual hospital or institution
employing the use of this equipment to implement a satisfactory
maintenance schedule may cause undue equipment failure and possible
health hazards.

«
1
2
3
4
...
»

Содержание 50 T Series










































































































Отзывы:

Нет отзывов

Похожие инструкции для 50 T Series

Бренд: DAPAudio Страницы: 12

Smart Sounddeck 100

Бренд: Canton Страницы: 58

DIGITAL MOVIE DM 90

Бренд: Canton Страницы: 68

Бренд: Canton Страницы: 8

Бренд: L-Acoustics Страницы: 38

Бренд: L-Acoustics Страницы: 36

Бренд: L-Acoustics Страницы: 31

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 55

Бренд: L-Acoustics Страницы: 201

Бренд: L-Acoustics Страницы: 16

Бренд: Neets Страницы: 14

Бренд: Roland Страницы: 12

Бренд: Niles Страницы: 2

Бренд: Eclipse Страницы: 8

Бренд: Konix Страницы: 8

Бренд: K&F Страницы: 38

Бренд: Malone Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды