Alignments
6.
Note:
Data of the 26" sets was not available at time of
publishing.
6.4
Option Settings
6.4.1
Introduction
The microprocessor communicates with a large number of I
2
C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these specific
ICs (or functions) is made known by the option codes.
Notes:
•
After changing the option(s), save them by pressing the OK
button on the RC
before
the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
•
The new option setting is only active after the TV is
switched “off” / “stand-by” and “on” again with the Mains
switch (the NVM is then read again).
6.4.2
Dealer Options
For dealer options, in SAM select “Dealer options”.
See Table
6-4 SAM mode overview (usage is model
.
6.4.3
(Service) Options
Select the sub menu's to set the initialisation codes (options) of
the model number via text menus.
See Table
6-4 SAM mode overview (usage is model
.
6.4.4
Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or “option byte”) represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set and in Table
“Option code overview”.
Example:
The options sticker gives the following option
numbers:
•
33280 36877 04299 45096
•
08406 00106 00368 00000
The first line (group 1) indicates hardware options 1 to 4.
Example: option no. “2” contains the “cabinet type”.
The second line (group 2) indicates software options 5 to 8.
Example: option no. “5” contains the “display code”.
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
See table
6-3 Option code overview (subject to change)
for the
options. Always refer to the sticker in the TV-set as leading.
Diversity
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM
An alternative BOM number usually indicates the use of an
alternative display. This results in another Display Code thus in
another Option code. Refer to chapter
.
6.4.5
Option Code Overview
Table 6-3 Option code overview (subject to change)
Note:
Option 2 is affected by the audio cabinet selection for
sound tuning, while option 5 is affected by the display code.
See also figure
6-1 Option code overview example
Important:
After having edited the option numbers as
described above, you
must
press OK on the remote control
before
the cursor is moved to the left!
6.5
Reset of Repaired SSB
For Component Level Repair (CLR) workshops:
A very
important issue towards a repaired SSB from a service repair
shop, implies the reset of the NVM on the SSB.
A repaired SSB in service should get the service Set type
“00PF0000000000” and Production code “00000000000000”.
Also the virgin bit must be set. To set all this, use ComPair.
For Board Level Repair (BLR) workshops:
If any
repair/servicing of TV sets (HFL model) requires the SSB to be
replaced,
you must write back the original TV serial number
into the new SSB
. This is done using the ComPair tool.
After verifying that the serial number has been written correctly,
you need to check (press MENU button using the Green RC) if
the set is in iTV mode. If it asks for a password, then you need
to enter the password to activate the Hotel mode.
For password generation, if you do not have access, please
contact your local helpdesk.
CTN_Alt-BOM
Disp.
code Options
26HFL5870D/10_1 214
33280 36877 04299 45096 08406 00106 00368 00000
32HFL5870D/10_1 213
33280 36877 04299 45096 08405 00106 00368 00000
37HFL5880D/10_1 201
33280 36877 04299 45096 08393 00106 00368 00000
42HFL5880D/10_1 205
33280 36875 04299 45096 08397 00106 00368 00000
