Philio Technology Corporation PSP06 Скачать руководство пользователя страница 9

Disposal

 

This marking indicates that this product should not be 
disposed with other household wastes throughout the EU. 
To prevent possible harm to the environment or human 
health from uncontrolled waste disposal, recycle it 
responsibly to promote the sustainable reuse of material 
resources. To return your used device, please use the 
return and collection systems or contact the retailer where 
the product was purchased. They can take this product for 
environmental safe recycling.

Philio Technology Corporation
8F.,   No.653-2,   Zhongzheng   Rd.,   Xinzhuang   Dist.,   New   Taipei   City
24257, Taiwan(R.O.C)

www.philio-tech.com

FCC Interference Statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency en-

ergy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one
of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including inter-

ference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This   transmitter   must   not   be   co-located   or   operating   in   conjunction
with any other antenna or transmitter.

警語

「取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變
更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,
應立即停用,並改善至無干擾時方得繼續使用。

前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合
法通信或工業、科學及醫療用電波輻射性電機設備之干擾。」

9

Содержание PSP06










Отзывы: