Philco PMDI 32, Руководство пользователя

Страница: 4 / 44

2
INSTALLATION INSTRUC
INSTALLATION INSTRUC INSTALLATION INSTRUC
INSTALLATION INSTRUCTIONS
TIONS TIONS
TIONS
Before installation
Check that the input voltage
Check that the input voltage Check that the input voltage
Check that the input voltage indicated on the characteristics plate is the same as the
voltage of the power outlet you are going to use.
Open the oven door and take out all the accessories and remove the pa
Do not remove the mica cover on the ceiling of the interior! This cover stops fat and
pieces of food damaging the microwave generator.
Warning! The front surface of the oven may be wrapped with a protective film. Before
using the oven for the first time, carefully remove this film, starting on the inside.
Make sure that the oven is not damaged in any way. Check that the oven door closes
correctly and that the interior of the door and the front of the oven opening are not
damaged. If you find any damage contact the Technical Assistance Service.
DO NOT USE THE OVEN if the power cable or the plug are damaged, if the oven does not
function correctly or if it has been damaged or dropped. Contact the Technical
Assistance Service.
Put the oven on a flat and stable surface. The oven must not be put close to any sources
of heat, radios or televisions.
During installation, make sure that the power cable does not come into contact with any
moisture or objects with sharp edges behind the oven. High temper
the cable.
After installation
The oven is equipped
The oven is equipped The oven is equipped
The oven is equipped with a power cable and a plug for single phase current.
If the oven is to be installed on a permanent basis it should be installed by a qualified
technician. In such a case, the oven should be connected to a circuit with an all
circuit breaker with a minimum separation of 3 mm between contacts.
a minimum separation of 3 mm between contacts. a minimum separation of 3 mm between contacts. a minimum separation of 3 mm between contacts.
WARNING: WARNING: WARNING: WARNING: THE OVEN MUST BE EARTHED.
The manufacturer and retailers do not accept responsibility for any damage that may be
caused to people, animals or property if these installation instructions are not observed.
The oven only functions when the door is closed correctly.
After the first use, clean the inside of the oven and the accessories, following the
cleaning instructions given in the section ‘‘Oven cleaning and maintenance
Fit the Turntable support in the centre of the oven cavity and
put the Turntable ring and the Turntable plate on top, making
sure they slot in. Whenever you use the microwave, the
turntable plate and the respective accessories must be inside
and correctly fitted. The turntable plate can rotate in both
directions.
During installation, follow the instructions supplied
During installation, follow the instructions supplied During installation, follow the instructions supplied
During installation, follow the instructions supplied
separately. separately. separately. separately.
indicated on the characteristics plate is the same as the
Open the oven door and take out all the accessories and remove the packing material.
Do not remove the mica cover on the ceiling of the interior! This cover stops fat and
Warning! The front surface of the oven may be wrapped with a protective film. Before
he first time, carefully remove this film, starting on the inside.
Make sure that the oven is not damaged in any way. Check that the oven door closes
correctly and that the interior of the door and the front of the oven opening are not
any damage contact the Technical Assistance Service.
DO NOT USE THE OVEN if the power cable or the plug are damaged, if the oven does not
function correctly or if it has been damaged or dropped. Contact the Technical
flat and stable surface. The oven must not be put close to any sources
During installation, make sure that the power cable does not come into contact with any
moisture or objects with sharp edges behind the oven. High temperatures can damage
with a power cable and a plug for single phase current.
If the oven is to be installed on a permanent basis it should be installed by a qualified
ould be connected to a circuit with an all-pole
a minimum separation of 3 mm between contacts. a minimum separation of 3 mm between contacts. a minimum separation of 3 mm between contacts. a minimum separation of 3 mm between contacts.
The manufacturer and retailers do not accept responsibility for any damage that may be
instructions are not observed.
After the first use, clean the inside of the oven and the accessories, following the
Oven cleaning and maintenance’’.