Adjusting the handle height
Your Kiwi Explorer Buggy
TM
is set at the lower handle height. To
increase the handle height:
• Remove the sun hood (pop the snap fasteners and gently pull
the sun hood wire free of frame).
• Disconnect the snap fasteners that secure the sling to the
frame, near the handle.
• Depress both nib springs located underneath each side of the
handle, and pull the handle up until springs re-engage. It can
be easier to un-zip each side of the main sling for this step.
The handle height is now reset.
• Reattach your sling to the snap fasteners but use the
lowest
fastener on each side of the handle. Zip the sling into place.
• Reattach the sun hood: carefully insert the sun hood wire
through the holes on the sling and frame; attach the snap
fasteners at the top of the sun hood to the
middle
fasteners on
each side of the handle.
•
To lower the handle
, reverse the above steps. In this position,
the snap fasteners on the sling attach to the middle fasteners
on each side of the handle; the sun hood attaches to the top
fasteners on the handle.
Using the sun hood
• To lock forward, secure the snap fasteners at each side of the
front of the sun hood to the fabric on the sling.
• To fold the sun hood down or when folding the buggy, release
the snap fasteners at the sun hood front. Lay the sun hood back.
• To remove the sun hood, release the snap fasteners on the
frame and fabric, on each side. The wire sits in a slot, so can
only remove when angled forward of the open position, with top
snaps released. Gently pull the support wire from the holes on
each side of the buggy.
Using the storm cover and sun/insect mesh cover
• Unfold the cover. Place over the sun hood, with the single snap
fastener to the buggy front.
• Fasten the cover with snap fasteners on the footplate and to each
side of the buggy.
• Fasten together snap fasteners at the rear/top of the cover
around the frame handle.
• Always use the webbing straps to remove the snap fasteners.
• Fold/unfold covers carefully. When cold, plastic hardens, loses
suppleness and may crack.
Useful Information
Doubles storm cover and sun/insect mesh cover
1 Unfold the cover.
2 Place over the sun hood, with the single snap fastener to the
buggy front.
3 Fasten the cover with one snap fastener on the footplate and two
on each side of the buggy.
4 Press together the velcro at the rear of the cover around the
handle bar, forming a roof for the rear seat.
5 Always use the webbing straps to remove the snap fasteners.
Fold/unfold carefully - plastic may harden and crack when
cold.
Warning: Ensure the parcel tray is securely in place as this is
the footrest for the rear doubles position
Doubles Fitting (carry 2 children)
WARNING: Never use the Double Buggy without a child in the front seat.
• Put the brakes on. Fit the rear sling (RS) to the doubles bar
(same as the main sling for Kiwi Explorer Buggy
TM
).
• Attach anti-fly straps at front of RS to sides of double bar.
• Insert each end of the bar into the plastic lined tubes on each
side of the buggy.
• Depress the ‘nib spring’ on each side and slide the bar home.
Check the buttons pop out once through. (See diagram below.)
• Place the older/heavier child in the front seat
first
.
• Place the younger/lighter child in RS.
Always get child in RS
out first
.
• The parcel tray is used as the RS foot rest. Connect the RS to
the tray using the snap fasteners and extra flap provided with
RS.
• Secure children with adjusted safety harnesses.
To remove the doubles kit:
• Put the brakes on.
• Depress the button springs on each side of the doubles bar.
• Pull bar out.
The complete double buggy
