Unpacking your Buggy
On arrival and setting up for the first time
•
Your buggy (frame and fabric items) will arrive in a box. Check the
box is not damaged.
•
The initial setup involves installing: wheels, front wheel J-Bar,
footplate, fabric items & handle.
Don’t worry - it’s easy - no tools needed.
Put the wheels on
Lie box on floor (TOP up). Carefully cut tape and lift off top. Check that
all components purchased are in the box. Check no components ap-
pear damaged. Carefully lift out wheels (2 rear and one front), bacpac
and frame. Place frame on floor, clicking auto-locks (A & B) in place.
Refer diagram above.
Attach the rear wheels by sliding each axle through the axle tubes. De-
press the ‘nib spring’ on each axle. Ensure nib pops out once through
axle. These hold the wheels in place. Remove wheels as required.
Attach front wheel:
Pull swivel wheel lock on pipe
out
(refer diagram);
aim J-bar to the side not front; depress nib spring and insert J-bar into
pipe; ensure nib spring pops at top and J-bar is flush with plastic bush;
push cap over pipe top.
Reverse procedure as required.
Put the parcel tray on
Pull the parcel tray forward so that it is in line with the ground. Loop
straps 1 & 2 (on both sides) around frame. Ensure strap 1 does not
catch the auto-lock pin. There is a snap on the inside of the frame
below the auto-lock. Loop strap 1
below
this snap. Loop the straps
in the centre of the tray (both sides) around the frame below doubles
bar tube. Attach rear strap 3 around the vertical frame at back of
buggy. Check it looks the same as the diagram.
Do not place more than 3kg/7lbs in the parcel tray.
Put the handle on
Slide the handle onto the frame. Ensure the holes in the handle
face
down
. There are two height settings. Depress the nib springs
on undersides of frame (twice for the lower setting).
1
Put the footplate on
Position footplate over front of buggy frame. Insert 4 plastic rivets
through holes in footplate; match to holes in frame. Rivet must rest on
footplate. DO NOT push stalk until rivet rests on footplate. Push (or
tap) rivet centre stalk, until flush.
2
3
5
Accessories
Call your Most Excellent Dealer for Accessories and Prices
J Bar
swivel
wheel
autolock on
pipe out
4
Explorer sleeping bag
Un-clip the breastplate.Thread the safety harness through the 5 slots
in the back of the sleeping bag. Attach the safety harness to the
breastplate. Fold down the front of the sleeping bag as required.
The sleeping bag top can be removed completely and the base used
as a buggy liner in warmer weather.
Remove the liners for separate washing. Follow fabric care label for
washing sleeping bag. Colours: Black or Blue
Travel bag
These bags help protect Kiwi Explorer Buggy
TM
. Remove the rear
wheels and place (axle-to-axle) together. Place Kiwi Explorer Bug-
gy
TM
in the travel bag and zip up bag. Carry with the shoulder or
hand straps. Because the fabric has a waterproof layer, storage of a
damp/wet Kiwi Explorer Buggy
TM
for long periods may result in fabric
mildew. Air dry. Colours: Black
Kiwi Explorer mattress
Made from the same fabric as the buggy, the mattress fits the base
of the newborn fitting. Guide the safety harness around the mattress.
Use the safety harness in the usual way.
The mattress can be used in the sitting position for extra back support
and comfort. Remove the mattress for cleaning. Fabric care as with
buggy fabric.
Kiwi Explorer bacpac
Made from the same durable fabric as the buggy, great for extra
storage and security. Attaches to the buggy (upper handle and lower
frame) with quick-release clips. Internal PVC compartment for soiled
items. Shoulder straps allow you to carry goods separate from the
buggy.
Embroidered with Kiwi Explorer. Removed easily for cleaning. Fabric
care as with buggy fabric.
Kiwi Explorer sun-insect mesh
Mesh protects from insects, wind and sun (SPF 6.5)
Fits same as storm cover.
Child Lifter
Sits in newborn position of buggy. Has a firm base and attaches us-
ing snap fasteners. Attach 5-point safety harness around child lifter.
Sleeping baby can be lifted from the buggy using two handles.
Made from the same durable fabric as the buggy and comes in
matching colours.
A
B
3
doubles bar tube
