least 2 holes on each bracket that line up over a wall stud. Drill the wall and install your anchors and fasten the brackets to the wall with the “J”
bend at the bottom (fig. 2 & 3).
Step 3
Place your TEATRO sound bar speaker face down on a soft clean surface with the grille on. Orient the speaker so the input terminal is on the
left hand side. The second pair of steel brackets supplied with the speaker is designed to attach to the threaded inserts on the rear of the
speaker cabinet with the 8 supplied #10-32x3/8” Philips screws. Simply align the holes on the brackets with the center and bottom set of
mounting holes on the rear of the speaker. Position the brackets similar to the ones mounted on the wall with the “J” bend up so it can hook
into the wall bracket. Attach brackets to the rear of the speaker using 4 screws per bracket (fig. 1 & 2).
Install one each of the 6, #10-32x1” Phillips screws in the threaded nut located in the bottom center of the “J” bend of the two wall mounted
brackets. These screws are for leveling the speaker. Just start the screws but do not screw in at this time.
Install the other 4, 1” screws in the end mounted nuts of the cabinet mounted brackets. These are the bracket locking screws and should be
install so they can be adjusted from the bottom of the speaker (fig. 3).
Assemble the 2 rubber stand-off bumpers next. Thread one nut onto each bumper stand-off and then one nylon washer. Run the nut about
half way down the screw. Thread each of the bumper stand-offs into the 2 lower inserts located on the bottom rear edge of the cabinet.
Step 4
There is 3 pair of gold binding post terminals
on the rear of the speaker cabinet. The
terminals are marked for
Right Input, Center
Input
and
Left Input
and should be
connected to the respective speaker channel
outputs on your receiver. Connect the
speaker wires to the correct terminals
observing the polarity indicated on the
terminal. Red is + or positive and black is – or
negative. Strip about ½” of insulation from the
wires and separate the wires as necessary. If
you are using other wire lugs or connectors,
attach them at this time to the bare wire.
Unscrew the binding post terminals and slip
the stripped end of the wire through the hole
in the metal post. Secure the wire in the post
by tightening the binding post terminal nut
down on the bare wire or lug. Make sure the
nut is tight and the wire will not pull out of the
terminal by lightly pulling back on the wire.
Tuck the speaker wire in behind the speaker
cabinet and if necessary or neaten up the
wire with the use of tie wraps.
Step 5
The TEATRO sound bar speaker is now
ready to be mounted to the brackets that
were screwed to the wall in step 2. The
brackets are made to interlock with each
other. Raise the speaker so the brackets on
the rear of the cabinet are aligned with the
wall brackets and engage the “J” bends in the
two sets of brackets together. If the speaker is being installed very close to the bottom of the flat panel display the speaker brackets can be
slid into each other from the side. After the brackets are interlocked, it is a simple matter to center the speaker by sliding it side to side. The
speaker can also be leveled by turning in the appropriate height adjusting screw to raise and lower the ends of the speaker. This is done with
a #2 Phillips screwdriver from the bottom side of the bracket. Once the speaker position is trimmed up it should be locked in place using the 4
locking screws in the speaker bracket (fig. 3). Be carful not to over tighten the screws.
Figure 1
RIGHT INPUT
CENTER INPUT
LEFT INPUT
USE THESE SETS OF HOLES
FOR SPEAKER BRACKETS FOR
NORMAL WALL MOUNTING
WALL MOUNT
BRACKETS
SPEAKER MOUNT
BRACKETS
FIGURE 2
SPEAKER MOUNTING BRACKETS HOOK
INTO WALL MOUNTING BRACKETS
STAND OFF BUMPER,
LOCK NUT, WASHER
FLAT PANEL WALL MOUNT
ATTACHMENT INSERTS
FIGURE 1
8 3/16”
