Install Instructions For:
P3-35 Outdoor
Install Instructions For:
P3-35 Outdoor
PAIRING WITH A BLUETOOTH DEVICE
PhaseTech
PhaseTech
1. Turn the P3-35 on by
pressing the on/off button.
The LED will turn white when
on.
2. Select PhaseTech on your
Bluetooth device to pair
them. If using the SoundTube
SB335, select SoundTube on
your Bluetooth menu.
3. Bluetooth (BT) will take
priority over a wired audio
signal when playing BT Audio.
When you stop or pause BT
audio the wired audio will
play.
EQUALIZER SETTINGS
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
1. Switches 2, 3, and 4 control
EQ settings. Each switch has
two positions - flat or +3dB.
2. To boost the low
frequencies, set Dip switch 2
to the up position (+3dB)
3. To boost the mid
frequencies, and increase
intelligibility set Dip switch 3
to the up position (+3dB)
4. To boost the high
frequencies, set Dip switch 4
to the up position (+3dB)
WEATHERPROOF BOX INSTALLATION INSTRUCTIONS
PRIOR TO INSTALLING:
The Weatherproof Box Kit comes fully assembled. Follow the instructions below for box mounting and amp set up.
1. Select the appropriate mounting location. While this box is weatherproof, it is best to locate the box where it is will not be
exposed to direct water. The Weatherproof box must not be submerged under water. It is recommended that the location be
near a hardwired weatherproof outlet with a GFCI. NO EXTENTION CORDS!
2. Be sure to mount the Weatherproof box such that the rubber membranes are facing down.
3. Mount Weatherproof box using appropriate mounting equipment (not supplied). Be sure the mounting location can support
the weight of the amp and box and that the box is securely installed.
4. NOTE: The volume control knob is disabled. Amplifier volume must be controlled by the input device: phone, audio player,
etc.
5. Amp comes preset in Sleep Mode. Sleep Mode enables auto-on input signal sensing and will turn the P3-35 on when there
is a signal present and will automatically turn off when there is no signal for 5-7 minutes.
6. The Weatherproof box comes equipped with a 12V cooling fan installed above the amplifier. The fan will turn on and off
automatically whenever the amplifier is running. No set up or adjustments are required for this fan.
WEATHERPROOF BOX INSTALLATION INSTRUCTIONS (CONTINUED)
PREPARE THE BOX - CUTTING THE MEMBRANE
1. Use a sharp knife to cut a “+” in the rubber membrane on
the left side of the box. The “+” cut must be large enough for
the IEC power cord connector to fit through the membrane.
2. Use a sharp knife and cut a “+” in the rubber membrane on
the right side of the box. The “+” cut must be large enough
for all of the required speaker wires and the signal input wire
to pass through.
PREPARE THE BOX - CONTINUED
1. Push the power cord through the “+” cut in the membrane on the left side of the box and connect it to the power supply.
2. Connect the speaker cables (not provided) to the supplied Euroblock (as described above). Push the Euroblock connector
through the “+” cut in the right membrane and plug into the amp.
3. If desired, push the RS232 control wires through the membrane on the right side and connect to the amp (as described
above).
4. If desired, push the analog or digital input wire through the membrane on the right side and connect to the amp (as
described above).
5. Select the appropriate dip switch setting for the desired features and performance (as described above).
6. If using the BlueTooth connection, position the antenna such that it will not interfere with the box lid when it is closed.
7. Close the Weatherproof box lid. If required, secure the lid with the included screw.
8. Now you are ready to connect to electricity. Connect power cord to GFCI outlet.
STANDBY AND SLEEP SETTINGS
There are two modes the P3-35 can operate in; Standby and Sleep. Setting the P3-35 in the standby mode disables the auto-
on input signal sensing. In this mode the P3-35 can only be turned on by pressing the Volume control On/Off switch or through
RS232 control.
Setting the P3-35 in the sleep mode enables auto-on input signal sensing and will turn the P3-35 on when there is a signal
present and will automatically turn off when there is no signal for 5-7 minutes.
Note: The P3-35 goes into standby mode 5-7 minutes after it stops sensing a signal provided the amp is set to standby mode.
The P3-35 will be switched into networked sleep mode in 5-7 minutes after it stops sensing a Bluetooth or wired audio signal
provided the amp is set in sleep mode.
SETTING THE OPERATION MODE
1. With the on/off switch in the off position (Red LED).
2. Press and hold the on/off switch for 10 seconds or until the LED starts blinking for 3 seconds.
3. If it blinks Blue it is in Sleep mode
If it blinks Green it is in Standby mode.
4. To change the mode repeat step 2.
