Install Instructions For:
P3-35 Outdoor
Install Instructions For:
P3-35 Outdoor
IMPORTANT SAFETY INFORMATION
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions
5. Do not use this apparatus near water, unless properly installed in the weatherproof box.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or object has fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture, unless properly installed in the
weatherproof box.
SPEAKER CONNECTIONS
STEREO
1 2 3 4 5 6
3 CHANNEL
1 2 3 4 5 6
1. To connect wires to the
Euroblock connector loosen
the screws, insert a 1/4” in of
stripped wire and tighten the
screws.
Note: make sure there are no
loose strands of wire.
1a. Make sure the + wire is
connected to the plus, or red
terminal on your speaker and
the – to the negative, or black
terminal on the speaker.
2. For 2 channels (Stereo),
connect your speakers to
the 2 outer sets L and R
terminals. Set dip switch 5 in
the up position.
3. For 3 channels, connect
the speakers to the two outer
sets of terminal for your left
and right channels and the
center set for the center
channel. Set dip switch 5 in
the down position.
CONNECTING A SUBWOOFER
1 2 3 4 5 6
1 2 3 4 5 6
1. Connect a powered
subwoofer to the P3-35 with
a RCA audio cable.
2. To use the built-in 120Hz
subwoofer crossover, set
dip switch 1 to the up (sub)
position.
3. To use an external Sub
crossover, set dip switch 1 to
the down (line) position.
CONNECTING YOUR WIRED AUDIO SOURCE
4 5 6
1. For digital connections, connect an optical cable from your
source to the optical input on the P3-35. Set dip switch 6 in
the down position. Note the amplifier volume is disabled and
must be controlled by the input device in this configuration.
2. For analog connections, connect a cable from your analog
source to the analog input using a stereo 1/8”mini-jack. Set
dip switch 6 in the up position. Note the amplifier volume is
disabled and must be controlled by the input device in this
configuration.
RS232 CONTROL
Baud Rate 115200
Data Bits 8
Parity none
Stop bit 1
Flow Control none
Ascii Description
UV1
Volume up one step
UV5
Volume up five steps
DV1
Volume down one step
DV5
Volume down five steps
MUTE 1 Mute
MUTE 0 Unmute
Ascii Description
GV
Get Volume setting
SV 0-81 Send Volume setting
AON
Amp on
AOFF
Amp off
Reset
Resets to factory default
1. Connect the RS232 control
device to the RS232 port on
the P3-35. Refer to Step 1
of “Speaker Connections”
for instructions on wiring the
Euroblock connector.
2. All serial commands should
be sent as listed above.
3. Ascii commands above are followed by a Carriage Return.
Note: The mute command is followed by a space then the
numerical value.
The SV command is followed by a space then the numerical
value of 0-81 to set the relative level.
All other alphanumeric variables have no space.
Reset sets the amp in sleep mode, volume at 40 and clears
the remote codes.
