Page 3
This section describes our recommendations to help you decide which accessories to purchase for your new aircraft.
Please read through this entire section very carefully. We have provided you with recommendations that,
if followed, will result in a great flying aircraft. Failure to follow our recommendations may result in a poor
flying aircraft.
Our reCOMMeNdatiONs
HiGH-PerfOrMaNCe aNd HOveriNG BrusHLess POWer systeM
reCOMMeNded radiO, reCeiver aNd servOs
l
KMS KBM 3/08 Brushless Outrunner Motor
l
KMS 8Amp Brushless ESC
l
APC 0 x 3.8 Slow Flyer Propeller
l
KMS Motor Adapter for Stick Mount
l
Impulse Power 3C 900mAH Li-PO Battery
l
ProPeak Quattro Li-PO DC Charger
Here's a List Of WHat We used tO fiNisH tHe QuiCK tiMe 3d eP sHOWN iN tHese iNstruCtiONs
You will need to use a transmitter with 4 or more channels and a 4 or more
channel micro receiver. Ideally, the transmitter should feature both dual and
exponential rates for the ailerons, elevator and rudder. The receiver should be
as light as possible, preferably around 9 grams.
The servos you use should be the lightest available, yet still have an adequate
amount of torque. We suggest using servos that weigh no more than 0 grams
and have a torque rating of no less than 0.8kg/cm (oz/in). Cirrus CS30 or similar micro servos will work well.
QTY. 6 Channel FM Transmitter
QTY. Cirrus 4 Channel FM Micro Receiver
QTY. Cirrus Crystal for Receiver
QTY. KMS KBM 3/08 Brushless Outrunner Motor
QTY. KMS 8Amp Brushless ESC
QTY. 4 Cirrus CS30 Micro Servos
QTY. APC 0 x 3.8 Slow Flyer Propeller
QTY. Impulse Power 3C 900mAH Li-PO Battery
QTY. ProPeak Quattro Li-PO Charger
QTY. KMS Stick Mount Adapter for KMS Outrunner Motors
QTY. 2 305mm (2") Servo Extensions
QTY. Y-Lead
QTY. Xtra 2mm Gold Connector Set
QTY. Double-Sided Tape
QYT. Velcro (Hook and Loop) Material
eCONOMy aerOBatiC BrusHLess POWer systeM
The Quick Time 3D EP can be flown using a variety of brushless direct drive motors. For the best flight performance (ideal for high
performance flight and hovering), use the power system recommended below. For 'economy' aerobatics, we recommend the Alternate
Brushless Power System. This power system will still provide spirited flight performance and is more inexpensive.
a WarNiNG aBOut WOrKiNG WitH ePP fOaM
l
KMS 2208/09 Brushless Motor
l
KMS 8Amp Brushless ESC
l
APC 0 x 3.8 Slow Flyer Propeller
l
Impulse Power 3C 900mAH Li-PO Battery
l
ProPeak Quattro Li-PO DC Charger
The Quick Time 3D EP is constructed of EPP foam. In addition to using 5 minute epoxy for assembly, you can use C/A (cyanoacrylate)
for a lot of steps to reduce the building time.
We don't suggest using any type of C/A accelerator or "Kicker" since these products can damage the factory-applied paint.
Do not use any harsh solvents, such as acetone, to clean the airframe. Harsh solvents will damage the factory-applied paint and
may melt the foam. It is okay to use rubbing alcohol. If you want to add more painted details to your aircraft, use water-based acrylic
paints and test on a scrap piece first.
