Pharmacia Biotech 18-1016-85 Скачать руководство пользователя страница 64

Страница: 64 / 114

8. Trouble shooting

Symptom

Cause

Remedy

Drying out of the gel

Incorrect electrode solutions

Use the recommended electrode

near the electrodes

solution at the specified
concentration.

Excessive power setting

Check the power setting

Sparking along edge

Excess moisture on gel or under

Remove the excess moisture

of gel onto cooling plate

cooling plate
Electrode strips overhanging the

Cut the electrode strips short

ends of the gel

of the ends of the gel

Liquid expelled at sides of electrode

Occasionally remove the excess

strips due to electroendosmotic flow

fluid by blotting

of water towards the cathode

Condensation over the

Excessive power setting

Check the power setting.

entire surface of the glass

When only a portion of the gel is

electrode holder

used, reduce the power setting
proportionally

Insufficient cooling

Check the temperature and flow
of the cooling fluid

Local condensation on

Local overheating due to a high salt

Reduce the salt content of the

the glass electrode holder

concentration in the sample

sample by gel filtration using
PD-10 columns pre-packed with
Sephadex G-25

Incorrect electrode solutions in relation

Check the electrode polarity.

to electrode polarity

Check the pH of the applied
electrode strips

Localized hot spots due to air

Use insulating fluid under the gel

bubbles under the gel

and check for air bubbles

Excessive amount of

Cathodic drift may cause an

Cut the electrode strips shorter

condensation along

electroendosmotic flow of water

than the edge of the gel. If

electrode strips

towards the cathode. Thus, cathode

necessary, blot the pooled liquid.

strip may become over saturated
Reversed polarity of electrode strips

Check pH of the strips and

(lower pH at cathode, higher

polarity of the plugs in the power

pH at anode)

supply. Reverse polarity if the
strips have been incorrectly
applied (should be acid at anode)

Skewed or wavy bands

Localized gradient disturbances

Reduce the salt content of the

due to excessive salt

sample by gel filtration using PD-
10 columns pre-packed with
Sephadex G-25. Salt content
should be <50 mmol/l.
Too much ammonium
persulphate may also cause wavy
bands

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 18-1016-85



















































































































Результаты поиска

Содержание 18-1016-85

Отзывы:

Бренды по названию

Популярные бренды

Pharmacia Biotech 18-1016-85, Руководство пользователя

Результаты поиска

Содержание 18-1016-85

Отзывы:

Бренды по названию

Популярные бренды