PGO Bug Rider BR-250 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 121

background image

2

. INSPECTION/ADJUSTMENT

8

BR 250 ENGINE

FINAL REDUCTION GEAR OIL

Stop the engine and remove the oil checks bolt.
The oil level shall be at the oil check blowhole.
If the oil level is low, add the recommended oil
SAE90# to the proper level.

Install the oil check bolt.

OIL CHANGE

Remove the oil check bolt.
Removes the oil drains bolt and drain the oil
thoroughly.
Install the oil drain bolt.

Torque

: 9.8N-m

Fill the final reduction with the recommended oil
SAE90#.

Gear Oil Capacity

:

At disassembly : 200cc
At change

: 180cc

Reinstall the oil check bolt and check for oil
leaks.

DRIVE BELT

Remove the left crankcase cover.
Inspect the drive belt for cracks or excessive
wear.
Replace the drive belt with a new one if
necessary and in accordance with the
Maintenance Schedule.

HEADLIGHT AIM

Turn the ignition switch ON.

Drive Belt

•

Place the motorcycle on its main stand on

level ground.

＊

Oil Drain Bolt/Sealing Washer

•

Make sure that the sealing washer is in

good condition.

＊

•

Make sure that the sealing washer is in

good condition.

＊

«
...
20
21
22
23
24
...
»

Содержание Bug Rider BR-250


























































































































Отзывы:

Нет отзывов

Похожие инструкции для Bug Rider BR-250

Бренд: Baja motorsports Страницы: 82

TRX90 Sportrax 90

Бренд: Honda Страницы: 208

Бренд: Suzuki Страницы: 502

Бренд: TrailMax Страницы: 58

Бренд: Iron Baltic Страницы: 44

Бренд: LONCIN Страницы: 56

Бренд: X-TREME Страницы: 26

Бренд: Global Страницы: 11

Бренд: Yamaha Страницы: 104

Бренд: Hammerhead Страницы: 24

Бренд: Taylor-Dunn Страницы: 232

Бренд: Taylor-Dunn Страницы: 260

Бренд: American Sportworks Страницы: 13

Бренд: Yamaha Страницы: 397

Бренд: Yamaha Страницы: 110

HAULER PRO 2014

Бренд: Cushman Страницы: 140

Бренд: Suzuki Страницы: 508

Бренд: Panther Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды