PGO Bug Rider BR-250 Скачать руководство пользователя страница 18

Страница: 18 / 121

. INSPECTION/ADJUSTMENT

BR 250 ENGINE

OIL LEVEL INSPECTION

Stop the engine and support the motorcycle
upright on level ground.
Wait for 2

∼

3 minutes and check the oil level

with the dipstick. Do not screw in the dipstick
when making this check.

OIL CHANGE

Remove the oil drain bolt to drain the engine oil.
Install the aluminum washer and tighten the oil
drain bolt.

Torque:

14.7N-m

Pour the recommended oil through the oil filler
hole.

Oil Capacity:

At disassembly: 1.1 liter
At change: 0.9 liter

Recommended Oil:

SAE: 15W40#
API: SG/CD
Start the engine and check for oil leaks.
Stop the engine and recheck the oil level.

OIL FILTER SCREEN INSPECTION

Drain the engine oil.
Remove the oil filter screen and spring.
Clean the oil filter screen.
Install the oil filter screen, spring, and filter screen
cap.
Fill the engine with recommended engine oil.

AIR CLEANER

Remove the eight air cleaner case cover screws
and the cover.

Spring

•

Drain the oil while the engine is warm.

＊

•

Replace the aluminum washer with a new

one if it is deformed or damaged.

＊

Oil Filter Screen

Oil Dipstick

Oil Filter Screen Cap

Содержание Bug Rider BR-250


























































































































Результаты поиска

Содержание Bug Rider BR-250

Отзывы:

Похожие инструкции для Bug Rider BR-250

Бренды по названию

Популярные бренды

PGO Bug Rider BR-250, Руководство по обслуживанию

Результаты поиска

Содержание Bug Rider BR-250

Отзывы:

Похожие инструкции для Bug Rider BR-250

Бренды по названию

Популярные бренды