PGO Bug Rider BR-250 Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 121

background image

11

. COOLING SYSTEM

15

BR & M2 250
ENGINE

THERMOSENSOR INSPECTION

Suspend the thermosensor in a pan of water
over a burner and measure the resistance
through the sensor as the water heats up.

Temperature(

℃

)

50

80

100 120

Resistance(

Ω

)

154

52

27

16

THERMOSENSOR INSTALLATION

Apply 3-BOND No. 1212 sealant or
equivalent to the thermosensor threads and
install it into the thermostat housing.
Connect the thermosensor wire.
Fill the radiator with coolant. (

ð

3-9)

Install the center cover, met-in box and seat.
(

ð

2-3)

THERMOSTAT

THERMOSTAT REMOVAL

Remove the seat, met-in box and center cover.
Drain the coolant.
Disconnect the thermosensor wire from the
thermosensor.
Disconnect the water hose from the thermostat
housing.
Disconnect the air vent tube from the thermostat
housing.
Remove the mounting bolt and the thermostat
housing from the cylinder head.

Remove the two bolts and separate the thermostat

Be sure to bleed air from the cooling
system.

＊

Thermosensor

Thermosensor Wire

Thermosensor Wire

Thermosensor

Thermometer

«
...
117
118
119
120
121
»

Содержание Bug Rider BR-250


























































































































Отзывы:

Нет отзывов

Похожие инструкции для Bug Rider BR-250

Бренд: LaTrax Страницы: 36

JACOBSEN 4800 2006+

Бренд: E-Z-GO Страницы: 114

Бренд: Arctic Cat Страницы: 123

Бренд: Hammerhead Страницы: 100

Wagon with tilt

Бренд: Texas Страницы: 42

Off-Roader 36EL

Бренд: Texas Страницы: 27

Бренд: Aosom Страницы: 5

Бренд: Fort Страницы: 88

Ranger 500 2x4 2007

Бренд: Polaris Страницы: 345

Бренд: U-Line Страницы: 9

Бренд: Jacobsen Страницы: 60

Бренд: Jayco Страницы: 124

2012 OCTANE SUPER LITE

Бренд: Jayco Страницы: 101

Бренд: Baja motorsports Страницы: 76

Бренд: Kellfri Страницы: 24

DewEze 400 Series

Бренд: Harper Страницы: 75

Бренд: Yamaha Страницы: 52

Бренд: CADDY Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды