PFT MULTIMIX Скачать руководство пользователя

Страница: 29 / 48

FORCED ACTION MIXER PFT MULTIMIX Overview – Operation – Spare Parts Lists

Maintenance

23.04.2018

Page 29

23.04. 2018

Personal protective equipment

Wear the following protective equipment for all maintenance work:

Protective work clothing

Safety goggles

Safety gloves

Safety shoes

36.3 Table of malfunctions

Malfunction

Possible cause

Solution

Performed by

Machine does
not start

Power cable is defective

Repair the power cable

Service technician

Main switch not activated

Turn on the main switch

Operator

Circuit breaker triggered

Reset the FI circuit breaker

Service technician

Safety shut-down triggered

Close the protective grille,
check safety switch

Operator

Machine does
not respond

Safety shut-down responds

Close grille, check switch

Operator

Material hopper too full

Disconnect and clean slide

Operator

Mixing unit has jammed
(stones too large)

Eliminate the cause of the jam
and start up again

Operator

Not enough water

Increase the quantity of water

Operator

Motor protection switch triggered
– too full or mixing unit jammed

Open slide and empty,
then start up again

Operator

37 Maintenance

37.1 Safety

Personnel

Unless otherwise stated, the maintenance work detailed

here can be carried out by the machine operator.

Some tasks may only be carried out by specially trained

personnel or only by the manufacturer.

Work on electrical systems must always only be carried out by

qualified electricians.

Содержание MULTIMIX

















































Результаты поиска

Содержание MULTIMIX

Отзывы:

Похожие инструкции для MULTIMIX

Бренды по названию

Популярные бренды

PFT MULTIMIX, Руководство по эксплуатации

Результаты поиска

Содержание MULTIMIX

Отзывы:

Похожие инструкции для MULTIMIX

Бренды по названию

Популярные бренды