PFT 00631891 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 56

PFT 00631891 Скачать руководство пользователя страница 31

Safety – Setting up and commissioning – Operation – Spare parts lists

Speed preselection for milling cutter, sawing and groove sawing power unit

2021-03-22

31

1530-Watt sawing unit,

longitudinal

1530-Watt sawing unit,

cross-cutting

1600-Watt sixfold sawing unit,

longitudinal cutting

Important!

Before installing any power unit, the power unit selection switch on the control panel must

be set to “0” or “Off” in order to prevent the power units starting up unintentionally.
Before switching on any power unit via the power unit selection switch, all units must be at

the top position of the machine; they must not be lowered into the material to be processed

until they have reached the correct speed.

If the power units are lowered into the material prior to this, and then switched on, this can

cause injuries to persons and permanent damage to the power units.

NOTE!
In this case the manufacturer is not liable for injury to persons or damage to material
If possible, always use the maximum speed (stage 5)!

To select the correct speed, observe the manufacturer’s instructions for the cutting tool used for the material

to be processed.

Important!

To change the power units, the control buttons must be switched off and the power unit

switches must be actuated. Switch off the main switch Disconnect the mains plug.
This prevents unintentional start-up of the power units. Follow the reverse order to start

up again.

Speed preselection for milling cutter units

«
...
29
30
31
32
33
...
»

Содержание 00631891

























































Отзывы:

Нет отзывов