Pfannenberg DTI 6201C Скачать руководство пользователя страница 33

Страница: 33 / 86

Operating Manual DTS and DTI 6201C / 6301C Multi-Controller (MC) 086100016 © Pfannenberg GmbH

Page 33 / 43

Error messages

Error

no.

Fault

Unit activity

Possible causes

Corrective measures

Er15

• LED:
• Compressor:
• Evaporator fan

(internal):

• Condenser fan

(external):

• Heater (external):
• Fault signal contact:

Blinking
OFF

OFF

OFF
OFF
Open



Anti-freeze (optional):



Anti-

freeze sensor ≤ 1°C.



Safety shut-off, because

there is a risk of icing of
the compressor.



Restart after

accumulating
condensate water has
evaporated.



A restart is only possible

with disconnection and
re-connection of the
mains voltage.



For safety reasons, there

is no other means of
resetting.



Clean the heat

exchanger fins
(internal/external).
Inspect the switch
cabinet for leaks.



Select higher switch

cabinet temperature
setpoint.



Check function of the

evaporator fan
(internal).

Er19

• LED:
• Compressor:
• Evaporator fan

(internal):

• Condenser fan

(external):

• Heater (external):
• Fault signal contact:

Blinking
OFF

OFF

OFF
OFF
Open



Sensor 5 (TS5) defective



Replace Sensor 5 or the

controller circuit board
according to the unit
type.

Содержание DTI 6201C























































































Результаты поиска

Содержание DTI 6201C

Отзывы:

Похожие инструкции для DTI 6201C

Бренды по названию

Популярные бренды

Pfannenberg DTI 6201C, Руководство по эксплуатации

Результаты поиска

Содержание DTI 6201C

Отзывы:

Похожие инструкции для DTI 6201C

Бренды по названию

Популярные бренды