Pfaff Creative 7550 Скачать руководство пользователя страница 85

Страница: 85 / 116

37. Exchanging the lower stepping motor

for

the

feed

movement

Note:

The feed stepping motor is only exchanged

omplete

Removal:

•

Remove the needle, the sewing foot and the needle plate.

•

Remove the top cover, the housing insert and the face cover.

•

Turn the machine upside down.

•

Unscrew the four screws of the baseplate

•

Turn the baseplate around.

•

Disconnect plugs 122 of the eight flat cables from the circuit board (fig. 37).

•

Press the two catches 1 17

motor plug 1 16 together and pull it off upwards.

•

Place the complete baseplate aside.

•

Open the two cable clips 119 at catch 1 20 and remove the cables form the cable clips.

•

Loosen fixing collar screw 33 of the synchronizer.

•

Remove the synchronizer to the right

from

the shaft

•

Remove the free-arm cover.

•

Remove the complete buttonhole sensor.

•

Remove the transverse-drive stepping motor according to section 38.

•

Unscrew screw 181 of cable guide 180 (fig. 37a).

•

Remove the cable guide 180 to the front

•

Disconnect pull-spring 14 (fig. 37b).

•

Unscrew screw 18.

•

Turn the handwheel until feeding eccentric 20 faces

the

back of the

rr..

..�t

•

Remove cam lever

folding

downwards. and pull it to the left off

lhe

s:i::Je

)Ck

ng with

link 10.

•

Remove slide block 1 2 to the right

•

Unscrew both screws 16 of the stepping motor.

•

Remove the complete feed stepping motor.

116-- -

117---

---117

Fig.�

Содержание Creative 7550





















































































































Результаты поиска

Содержание Creative 7550

Отзывы:

Pfaff Creative 7550, Руководство по обслуживанию, Страница: 85 / 116

Результаты поиска

Содержание Creative 7550

Отзывы: