Pfaff Creative 7550 Скачать руководство пользователя страница 115

Страница: 115 / 116

49.

Stray current

test of complete motors with

ABB

Metrawatit M

5013

Stray

current test

of complete motors

•

When exchanging complete motors or motor parts (windings, rotors or capacitors),

the complete motor must be measured for stray currenl before fitting

the machine.

Set knob for measuring range at

"20

mA" (fig.

)

•

Screw on nut (part No.

92-320 068-{)5)

at the motor.

•

Push auxiliary angle plug (part No.

29-924 800-04)

onto the motor plug.

•

Attach the

two

test le:ads as shown in fig.

49.

Meter reading: maximum

0.75

mA.

50.

Measures

required

in case

test

values

to I)

one of the

test functions

a failure, the ground mains socket is

def

ective

Inform the landlord.

As to

11)

the current consumption deviates considerably from the indicated va.lue.

although

the

machine does not bind, the motor is defective and must

exchanged

or repaired.

As to

Ill)

the insulation resistance drops below the required value, the defective components

must

found by systematic checking and must be repaired or replaced.

As to IV)

Here,

the

components with lnadmissably high leakage current must also

found

by systematic checking and must

repaired.

to V)

Send the motor

to the

factory.

Karlsruhe,

March,

1994

PH/HTSC

114

Содержание Creative 7550





















































































































Результаты поиска

Содержание Creative 7550

Отзывы:

Pfaff Creative 7550, Руководство по обслуживанию, Страница: 115 / 116

Результаты поиска

Содержание Creative 7550

Отзывы: