Pfaff admire air 5000 Скачать руководство пользователя страница 40

Страница: 40 / 44

40 –MACHINE MAINTENANCE

Replacing the Upper Cutter

Turn off the main power switch and unplug the machine.

The upper cutter should be changed when it becomes

blunt. Change it by following the below instructions. If

you are having any difficulties, have a service technician

make the necessary adjustments.
• Open the front cover.
• Place the upper cutter in its highest position.
•

Loosen the upper cutter set screw (A) with the

double-ended wrench (use the small end) and remove

the upper cutter (B).

•  Place a new upper cutter to the upper cutter holder (C)
•  Tighten the upper cutter set screw (A) partially.
•  Place the upper cutter in its lowest position.
•  Adjust the position of the upper cutter until the front

edge of the upper cutter is approx 1-1.2mm lower than

the cutting edge of the stationary cutter (D).

• Tighten the upper cutter set screw (A) completely.

Troubleshooting

Machine Does not Run

Possible Cause:

Machine not properly connected to power source.

Solution:

Check that machine has been properly connected to power source (page 7).

Possible Cause:

The safety device is activated.

Solution:

Close open covers (page 8).

Fabric Does not Feed Well

Possible Cause:

Stitch Length is set too short for the fabric being sewn.

Solution:

Increase the stitch length setting (page 26).

Possible Cause:

Differential Feed is not set in the correct position for the fabric being sewn.

Solution:

Adjust the Differential Feed (page 25).

Possible Cause:

Presser foot pressure is not correctly set for fabric being sewn.

Solution:

Adjust presser foot pressure (page 25).

Irregular Trimming

Possible Cause:

Upper cutter is not in proper position.

Solution:

Check alignment of cutters (page 40).

Possible Cause:

Cutter is damaged or worn out.

Solution:

Replace the upper cutter (page 40).

Содержание admire air 5000












































Результаты поиска

Содержание admire air 5000

Отзывы:

Похожие инструкции для admire air 5000

Бренды по названию

Популярные бренды

Pfaff admire air 5000, Руководство пользователя

Результаты поиска

Содержание admire air 5000

Отзывы:

Похожие инструкции для admire air 5000

Бренды по названию

Популярные бренды