manualshive.com logo in svg

Pfaff 3834-3/11, Инструкция по эксплуатации, Страница: 42 / 48

Поделиться
Скачать
Pfaff 3834-3/11 Скачать руководство пользователя страница 42

42  PFAFF

List of error messages

E00-SIZE

E01-FD. ROLL-P.

E02-ST. LENGTH

E03-PROG. NO.

E04-PROG. DATA

E05-SL. ST. SPEED

E06-GRADING

E07-GRADE VAL.

E13-PEDAL ACT.

E15-SEAM LENGTH

E16-SEGMENT NO.

E17-MAX. SPEED

E19-SEGM. DATA

E22-SEW. MOTOR

E23-SEW. MOTOR

E24-SEW. MOTOR

E25-SEW. MOTOR

Selected size is not valid or a size of a different size system has
been selected. For valid sizes see page 33.

Error in selection of roller presser feed motion (possible only from 0.8
to 5.0 mm).

Error in selection of wheel feed (possible from 0.8 to 5.0 mm only).

Invalid program number input (valid program numbers for “sewing”
mode are 0 to 24, for “input” mode 1 to 24).

Input of invalid data or selection of a program that has not been
programmed.

Input of invalid slow start stitches speed (valid from 100 to 1500 r.p.m.).

The inputted grading is invalid. Unsuccessful attempt to grade with
enabled knee switch.

Input of invalid grading value (valid form 1 to 50 mm).

Pedal was engaged when switching on the machine.

Input of invalid seam length (valid from 1 to 999 mm).

Input of invalid segment number (valid from 1 to 15).

Input of invalid maximum speed (valid from 100 to 3200 r.p.m.).

Invalid segment data.

Error when reading the setting number.

Error when reading status word “angle”.

Sewing drive communication error when positioning needle in b.d.c.

Sewing drive communication error when positioning needle in t.d.c.

Содержание 3834-3/11

















































Отзывы:

Нет отзывов