PEUGEOT SPEEDFIGHT 3 RS Скачать руководство пользователя страница 55

Страница: 55 / 60

FUEL SYSTEM

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

Removal of the pick-up pump

- Remove the 2 screws from the sheathing

holder plate.

- Remove the bushing (1) and the protective

rubber (2).

Check the condition of the

bushing and the rubber protection.

- Remove the piston (3).

Removal of the pick-up pump suction

valve

- Remove the jet.
- Remove the spring.
- Remove the ball.

Removal of the deceleration

enrichment device

- Remove the 2 bolts that secure the cover.
- Remove the cover.
- Remove the spring.
- Remove the membrane.
- Remove the O ring.

Check that the membrane is in

good condition.

Check the condition of the O-ring.

Содержание SPEEDFIGHT 3 RS





























































Результаты поиска

Содержание SPEEDFIGHT 3 RS

Отзывы:

Похожие инструкции для SPEEDFIGHT 3 RS

Бренды по названию

Популярные бренды

PEUGEOT SPEEDFIGHT 3 RS, Руководство по ремонту

Результаты поиска

Содержание SPEEDFIGHT 3 RS

Отзывы:

Похожие инструкции для SPEEDFIGHT 3 RS

Бренды по названию

Популярные бренды