manualshive.com logo in svg

PEUGEOT SPEEDFIGHT 3 RS, Руководство по ремонту

ПЕЖО СПИДФАЙТ 3 RS - это современный и стильный мопед, предлагающий уникальный опыт вождения. Для полного ознакомления с возможностями этого устройства, вы можете бесплатно скачать брошюру и руководство по эксплуатации на manualshive.com. Получите всю необходимую информацию для безопасного и комфортного использования вашего мопеда.

Поделиться
Скачать
background image

TABLE OF CONTENTS

2

Reproduction or translation, even partial, is forbidden without the written consent of Peugeot Motocycles

Removal of front lower shield panels .......................................................................................................23

Removal of the footboard .........................................................................................................................24

Removal of the under body panel ............................................................................................................24

SERVICE OPERATIONS................................................................................................................................. 25

Changing the engine oil ...........................................................................................................................25

Draining the relay box ..............................................................................................................................26

Removal of the spark plug .......................................................................................................................27

Replacing the air filter. .............................................................................................................................27

Transmission ............................................................................................................................................28

Checking the drive belt ............................................................................................................................30

Checking the clutch linings ......................................................................................................................31

Replacing the clutch lining assembly .......................................................................................................31

Installing the valve clearance ...................................................................................................................32

Idle setting................................................................................................................................................33

Brake inspection ......................................................................................................................................34

Replacing the brake pads ........................................................................................................................34

Checking the brake fluid level ..................................................................................................................35

Rear brake linings ....................................................................................................................................36

Disassembly...................................................................................................................................................... 36

Reassembly ...................................................................................................................................................... 37

Removal of the fuel filter ..........................................................................................................................38

STEERING/FORK............................................................................................................................................ 39

Changing the front fork seals ...................................................................................................................39

Removal of the fork tubes ........................................................................................................................41

The fork and its components....................................................................................................................42

Removal of the fork ..................................................................................................................................43

Replacing the steering head cups............................................................................................................44

Installing the fork......................................................................................................................................45

Steering system tightening method..........................................................................................................45

ELECTRICITY.................................................................................................................................................. 47

Ignition principle schematic/Carburetor heater ........................................................................................47

Temperature control unit/Regulator/Starter motor relay/Ignition unit .......................................................48

Checking the carburettor heating circuit...................................................................................................48

Checking the ignition system ...................................................................................................................49

Fuel gauge ...............................................................................................................................................49

Содержание SPEEDFIGHT 3 RS





























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDFIGHT 3 RS

medemagroup Mini Crosser X1 Cabin Quick Manual preview
Mini Crosser X1 Cabin
Бренд: medemagroup Страницы: 20
VELOCIPTOR NRG es 8Ew User Manual preview
NRG es 8Ew
Бренд: VELOCIPTOR Страницы: 57
Lambretta Uno50 Owner'S Manual preview
Uno50
Бренд: Lambretta Страницы: 124
IO Hawk EXIT-CROSS ENTRY User Manual preview
EXIT-CROSS ENTRY
Бренд: IO Hawk Страницы: 42
BAnff eProdigy series Assembly Manual preview
eProdigy series
Бренд: BAnff Страницы: 21
DAELIM NS 125 DLX Owner'S Manual preview
NS 125 DLX
Бренд: DAELIM Страницы: 66
Suzuki UZ125 Owner'S Manual preview
UZ125
Бренд: Suzuki Страницы: 117
Hudora 14695 Instructions On Assembly And Use preview
14695
Бренд: Hudora Страницы: 16
Huffy Pro Owner'S Manual preview
Pro
Бренд: Huffy Страницы: 8
CareCo TITAN Owner'S Manual preview
TITAN
Бренд: CareCo Страницы: 23
2GOability Boost User Manual preview
Boost
Бренд: 2GOability Страницы: 30
BOOSTBIKES Scout Owner'S Manual preview
Scout
Бренд: BOOSTBIKES Страницы: 16
Blaze scooters Blaze 600 Smart Lithium Scooter Manual preview
Blaze 600 Smart Lithium Scooter
Бренд: Blaze scooters Страницы: 10
UBCO 2x2 Dual-Use 2018 User Manual preview
2x2 Dual-Use 2018
Бренд: UBCO Страницы: 57
E-TON Beamer & Beamer Owner'S Manual preview
Beamer & Beamer
Бренд: E-TON Страницы: 29
Baja motorsports SC150 HSun 150cc Setup Instructions preview
SC150 HSun 150cc
Бренд: Baja motorsports Страницы: 11
Jetson JOURNEY Manual preview
JOURNEY
Бренд: Jetson Страницы: 24
Kaabo Skywalker 8 User Manual preview
Skywalker 8
Бренд: Kaabo Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды