manualshive.com logo in svg

Peugeot Motorcycles Scoot'elec, Руководство по ремонту

Поделиться
Скачать
Peugeot Motorcycles Scoot'elec Скачать руководство пользователя страница 8

SPECIAL IMPORTANT POINTS

Page: 8

Reproductions or translations, even partial, are forbidden without the written consent of Peugeot Motocycles

SPECIAL IMPORTANT POINTS

The scoot'elec is fitted with a coded immobiliser. This system prevents the machine from being started if the
user has not entered the secret code number. See instructions page 19.

Charging of the 3 Cadmium-Nickel batteries is by means of the on-board charger fitted with a 220V 10/16A
power connector with earth.
A partial charge may be carried out, and each charge of 10 minutes enables approximately 5 km to be
covered in ECO mode.

If the battery temperature is high, charging will only commence after the time it takes to cool down which is
controlled automatically by the charger and the ECU (which means that the charging time will be prolonged

by the same time). The 

 lamp will flash until the charge is triggered automatically. See instructions page

6.

Содержание Scoot'elec

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды