Perlight Solar PLM-OM Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 19

Perlight Solar PLM-OM Series Скачать руководство пользователя страница 15

Perlight Solar PLM-OM Series Installation Manual

15

www.perlight.com

V.01.2022 A1.0

9. Module Wiring

Each solar module is wired with two separate series cell strings.

Bypass Diodes

Bypass diodes are wired in parallel with the series cell strings to prevent hot spot heating

caused by individual cell reverse bias that occurs when a module is partially shaded.

Output Cables

Each module has two standard 90°C rated, water-proof, UV resistant output cables each

terminated with plug & play connectors. This cable is suitable for applications where wiring is

exposed to the direct rays of the Sun.

Field connections

Connecting cables should be a minimum of 12 AWG copper cables, which are UV resistant

and insulated for a minimum of 90°C. All wiring and electrical connections must comply with

local and national Electrical Code.

Blocking Diodes

In a system utilizing a battery, blocking diodes are typically placed between the battery

and the solar module output to prevent battery discharge at night. Diodes that are used as

blocking diodes must: Have a Rated Average Forward Current [IF(AV)] above maximum

system current at highest module operating temperature. Have a Rated Repetitive Peak

Reverse Voltage [VRRM] above maximum system voltage at lowest module operating

temperature.

«
...
13
14
15
16
17
...
»

Содержание PLM-OM Series




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды