Perlick BR48 Скачать руководство пользователя страница 4

4

Perlick is committed to continuous improvement. therefore, we reserve the right to change specifications without prior notice.

Preparing the Cabinet for Use

Form no. Z2278

rev. 05.06.10

Parts List 

  ■ 

(2) Shelves plus (1) Floor rack-per door.

  ■ 

Shelf Clips.

Suggested Tools 

  ■ 

 #2 Phillips Screwdriver.

  ■ 

10” Crescent Wrench.

  ■ 

9

/

16

” allen Wrench.

  ■ 

5

/

16

” and 

3

/

8

” hex Socket.

  ■ 

Power Drill or Driver. 

Plumbing 

Condensate from the cooling coil is automatically 
evaporated through a condensate pan located in the 
condensing unit housing. each unit is also equipped 
with a floor drain located in the right rear corner of 
the cabinet. the drain can be plumbed to an external 
floor drain by connecting to the 

3

4

” nPt thread out 

the side or the 1” nPS thread out the bottom. both 
drains ports come plugged from the factory and can 
be removed if needed.

NOTE:

remote units require evaporator condensate to be 
plumbed to an external drain. 

Electrical 

the cabinet must be connected to a separately 
fused power source (see electrical specification
plate) and grounded in accordance with national 
and Local electrical Codes. Caution: Do not
attempt to operate the equipment on any other 
power source than that listed on the electrical
Specification plate.

Uncrating and Inspection 

remove all crating material before operating. 
Carefully inspect cabinet for hidden damage. if
damage is discovered, file your claim immediately 
with the transportation company. Perlick is
not responsible for damage in transit.

Installing Casters and Legs 

(Optional)

 

attach four casters to the cabinet bottom; rigid cast-
ers at the rear and swivel casters on the front. Use 
the supplied 

1

/

4

”- 20 x 

3

/

4

” hex head self-tapping 

machine screws.

Placing the Cabinet 

Push the cabinet into place using rollers when  
necessary. 

Important:

 Proper air flow around the 

condensing unit is necessary for efficient operation. 
never obstruct the air flow in and out of the  
condensing unit.

For sanitation purposes, it may be necessary to 
seal the base of the cabinet to the floor. this can be 
accomplished by laying a bead of silicone sealant 
between the base of the cabinet and the floor as 
shown by  the figure at below.

Leveling the Cabinet 

When the cabinet is in place, check installation with 
carpenter’s level. When level front to back and left 
to right, accumulated water will drain out of cabinet 
evaporator drain.

Installing base Plate 

(Optional)

 

attach brackets to cabinet bottom in holes pro-
vided. attach base plate to brackets. (See separate 
instructions, provided with kit). When returning 
cabinet to upright position, be careful not to bend 
brackets.

WARNING! 

To avoid compressor damage, after returning  

cabinet to an upright position, let unit stand for  

24 hours before plugging it in and running the unit.

beaD SiLiCOn

SeaLer (rtV)

FLOOr

Cabinet

Содержание BR48









Отзывы: