background image

Installation                                                                                                       20

IDS-509F Hardware Installation Guide

Connecting Data Ports

Ethernet Connections

By default all of the 10/100/1000 ports will automatically set themselves up to match the 

speeds of all attached devices. If auto negotiation is not supported by one or more attached 

devices, the ports can be configured to operate at fixed speeds and duplex settings.

Warnin

g: 

In hazardous location installations, failure to remove the power from the source 

prior when completing the wiring connections to the Ethernet ports could cause an electri

-

cal arc resulting in a possible explosion.

To connect to 10Base-T, 100Base-TX or 1000Base-T follow these steps:

1. When connecting to devices, workstations, servers or routers connect a straight 

through Ethernet cable to a 10/100/1000 RJ45 connector on the front of the IDS 

switch. Gigabit Ethernet requires CAT5 or better.

2. Once the device is connected and link is established the link LEDs will turn on. These 

LEDs will indicate whether you have a 10,100 or 1000 Mb/s link to the switch. See. 

(LED Indicators) for more details.

Note: 

It may take a few seconds for the device to become active. By default the IDS 

switch will have Rapid Spanning Tree (RSTP) protocol enabled. This protocol will first 

check the network for any cabling loops prior to bringing the port up, in order to prevent 

network disruptions.

Fiber Connections

To connect to 100Base-X follow these steps:

1. Connect 100Base-X devices to the fiber ports using appropriate fiber cables. Ensure 

that cable implements the proper the TX to RX crossover

2. Once the device is connected and link is established the link LEDs will turn on.The 

LED will begin to flash once data activity is initiated. See. (LED Indicators) for more 

details.

Note: 

It may take a few seconds for the device to become active. By default the IDS 

switch will have Rapid Spanning Tree (RSTP) protocol enabled. This protocol will first 

check the network for any cabling loops prior to bringing the port up, in order to prevent 

network disruptions.

Содержание IDS-509F






































Отзывы: