Perle IDS-409-SFP Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

background image

Installation 24

IDS-409-SFP Hardware Installation Guide

Fast Setup Mode

This allows you to perform initial configuration of the switch using your Web browser.
Fast Setup Mode can be activated when the switch is in Factory Default. When started up
in this mode, the switch assigns itself an IP address and also assigns an IP address to the
connected PC. This makes it possible to initiate a Web session and the use of the Fast
Setup configurator. Switches are shipped in Factory default mode. Refer to the Quick Start
Guide that came with the switch for instructions on how to connect to the switch for the
first time.

Password Recovery

When the switch is not in factory default, the "Fast Setup Mode" sequence will activate
Password recovery.

Note

: The password recovery feature can be disabled in the software.

SYS

Green blinking - Boot process underway.

LED

Behavior

LED

Behavior

PWR

Press and hold the Reset/FS button.
Release button when LED changes from
Red to Yellow.

Port Link
/ Speed

Rapid blinking on the first available RJ-
45 port to which the PC can be connected.

LED

Behavior

ALR

On solid - during reset process
Off - to indicate that reset has completed

«
...
24
25
26
27
28
...
»

Содержание IDS-409-SFP









































Отзывы:

Нет отзывов

Похожие инструкции для IDS-409-SFP

D-PFS4226-24ET-240

Бренд: Dahua Страницы: 58

Бренд: X10 Страницы: 20

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: National Instruments Страницы: 32

Бренд: B&B Electronics Страницы: 22

ServSwitch KV1510A

Бренд: Black Box Страницы: 16

Бренд: VeEX Страницы: 22

Бренд: DX Engineering Страницы: 4

AVlink VAX-8404F

Бренд: C&C TECHNIC Страницы: 2

Бренд: Leaksafe Solutions Страницы: 12

Бренд: Copal Страницы: 9

Бренд: Banner Страницы: 8

LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED

Бренд: 3Com Страницы: 186

Бренд: Audioplex Страницы: 8

Бренд: Hirschmann Страницы: 50

Draco tera K480-80C

Бренд: Ihse Страницы: 214

PDU-ATS-100A-208Y.120-3PH

Бренд: Larson Electronics Страницы: 14

HIRSCHMANN MACH 4000 Series

Бренд: Belden Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды