Perle 07016830 Скачать руководство пользователя

Страница: 10 / 40

Overview 8

IDS-509-SFP Hardware Installation Guide

LED Indicators

P (Power Inputs)

Sys (System Status)

Alr (Alarm)

BC (Backup Coupling)

State

Description

Green

P1 and P2 Power inputs within specifications

Yellow

P1 or P2 Providing power within specifications

Red

Neither P1 or P2 providing power within specifications

State

Description

Green - blinking (after power on)

System booting

Green - solid

System ready/operating normally

Green - blinking slowly

Fast Setup Mode activated/port available

Green - blinking fast

Fast Setup Mode activated/no port avail-
able

Red

Hardware fault or firmware load error

State

Description

Off

No alarms configured

Green - solid

Alarms configured, but no alarms detected

Red - solid

Alarm condition detected

Red - blinking

Alarm condition detected and Alarm Relay activated

State

Description

Off

Backup Coupling not enabled

Green - solid

Backup Coupling Link enabled

Содержание 07016830









































Результаты поиска

Содержание 07016830

Отзывы:

Похожие инструкции для 07016830

Бренды по названию

Популярные бренды

Perle 07016830, Руководство по установке оборудования

Результаты поиска

Содержание 07016830

Отзывы:

Похожие инструкции для 07016830

Бренды по названию

Популярные бренды