Perkins 5006A-E23TA Скачать руководство пользователя страница 81

Страница: 81 / 100

Illustration 78

g06650982

Typical example

Install a suitable tube onto the drain (2). Open the

drain (2). Allow the fluid to drain into the container.

When only fuel free of water is draining, tighten the

drain (2) by hand pressure only. Remove the tube
and dispose of the drained fluid in accordance with
local regulations and mandates.

i08391556

Fuel

System

Secondary

Filter

Replace

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

Ensure that the engine is stopped and the battery is
isolated, before any servicing or repair is performed.

A fuel temperature sensor and two fuel pressure
sensors are mounted in the fuel filter base. The

Engine Control Module (ECM) uses the sensors to
monitor the temperature and pressure of the fuel that
is entering the engine.

The electronic service tool (EST) can be used to
monitor the fuel pressure. Contact Perkins distributor
for more information.

Illustration 79

g06309402

Typical example

Ensure that the fuel supply valve is in the OFF

position.

Clean the outside of the secondary and tertiary fuel

filters.

Use a suitable strap wrench to remove the tertiary

fuel filter (3) and discard the old tertiary fuel filter.

Lubricate the O ring seal (2) on the new tertiary

fuel filter with clean engine oil. Ensure that the
sealing surface (1) is clean and free from dirt.

Installed the new fuel filter by hand only. When the

O ring seal (2) contacts the sealing surface (1),
rotate the tertiary fuel filter 1 full turn.

Repeat Step 3 through Step 5 for the secondary

filter (4).

Remove the container and dispose of the fuel in

accordance with local regulations.

Restore the fuel supply to the engine.

Prime the fuel system. Refer to the Operation and

Maintenance Manual, “Fuel System - Prime” for
more information.

M0122761

Maintenance Section

Fuel System Secondary Filter - Replace

Содержание 5006A-E23TA




































































































Результаты поиска

Содержание 5006A-E23TA

Отзывы:

Perkins 5006A-E23TA, Руководство по эксплуатации и обслуживанию, Страница: 81 / 100

Результаты поиска

Содержание 5006A-E23TA

Отзывы: