Perkins 5006A-E23TA Скачать руководство пользователя страница 58

Страница: 58 / 100

Visually inspect fan guards for wear or damage.

Repair as necessary. Remove the fan guards (1).

Inspect the belts for cracks, splits, glazing, grease,

displacement of the cord and evidence of fluid
contamination. If necessary, replace the belts,
refer to “Replace” for more information.

Adjust

Ensure that the electrical supply to the engine is

isolated.

Using a suitable belt tensioning tool, check the

tension of the fan belts. the belt tension should be
checked in the middle point between the two
pulleys.

• New belt tension should be set to 49 N (11. lb)

• Belt tension range should be from 31 N to 49 N

(6.9 lb to 11 lb)

• Belt deflection should be 4.2 mm (0.165 inch)

Illustration 43

g06619955

Each belt must be checked.

Loosen nuts (4) on fan adjuster plate (5). Loosen

lock nut (3).

Turning bolt (2) counter-clockwise will adjust fan

pulley (6) and loosen the fan belts (7).

Turning bolt (2) clockwise will adjust fan pulley (6)

and tighten the fan belts (7).

When the fan belts (7) are at the required tension,

tighten nuts (4) to a torque of 85 N·m (62 lb ft).
Then, tighten nut (3) securely.

M0122761

Maintenance Section
Belts - Inspect/Adjust/Replace

Содержание 5006A-E23TA




































































































Результаты поиска

Содержание 5006A-E23TA

Отзывы:

Perkins 5006A-E23TA, Руководство по эксплуатации и обслуживанию, Страница: 58 / 100

Результаты поиска

Содержание 5006A-E23TA

Отзывы: