Perkins 5006A-E23TA Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 100

Perkins 5006A-E23TA Скачать руководство пользователя страница 80

Illustration 77

g06597518

1.

Isolate the fuel supply to the engine.

2.

Place a suitable container under the fuel filter to

catch any fuel that might spill. Clean up any spilled
fuel immediately. The engine is equipped with two
primary fuel filters all the primary filter must be
replaced.

3.

Clean the outside of the fuel filters. Open the drain

valve (7) on both primary fuel filters and allow the
fuel to drain.

4.

Remove Water In Fuel (WIF) sensor (6).

5.

If necessary, cut cable strap (4) and disconnect the

WIF sensor from harness assembly (3).

6.

Use a suitable strap wrench to remove the primary

fuel filter (2) from fuel filter head (). Discard the fuel
filter.

7.

Ensure that the sealing surface (8) is clean the free

from dirt. Lubricate O ring seal (9) on the new
primary fuel filters with clean fuel oil.

8.

Install the new primary fuel filter to the fuel filter

head using hand pressure only. When the O ring
seal (9) contacts the sealing surface (8), rotate the
primary fuel filter 3/4 of a turn.

9.

Repeat Step 6 through Step 8 for the remaining

fuel filter.

10.

Install new O ring seal (5) to the WIF sensor.

11.

Install the WIF sensor.

12.

If necessary, connect the WIF sensor to harness

assembly (3) and install new cable strap (4).

13.

When the primary fuel filters have been replaced,

the secondary fuel filters must be replaced. Refer
to “Operation and Maintenance Manual”
Secondary Fuel Filter- Replace for more
information.

i08383275

Fuel

System

Primary

Filter/

Water

Separator

-

Drain

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire. To help prevent
possible injury, turn the start switch off when
changing fuel filters or water separator elements.
Clean up fuel spills immediately.

NOTICE

Ensure that the engine is stopped before any servic-
ing or repair is performed.

1.

Place a suitable container under the fuel filters (1)

to catch any fuel that might spill. Clean up any
spilled fuel.

80

M0122761

Maintenance Section
Fuel System Primary Filter/Water Separator - Drain

«
...
78
79
80
81
82
...
»

Содержание 5006A-E23TA





































































































Отзывы:

Нет отзывов