Perkins 4006D-E23TA Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 88

Perkins 4006D-E23TA Скачать руководство пользователя страница 70

Illustration 53

g01238304

Typical example

2.

Remove the guards (not shown) to gain access to

the fan drive pulley (1).

Illustration 54

g01238305

3.

Tighten the grub screws (2) to a torque of 90 N·m

(66 lb ft).

4.

Install the guards (not shown).

5.

Restore the electrical supply to the engine.

i07426644

Fuel

Injector

-

Inspect/Adjust

Note:

Perform

this

procedure

when

the

engine

valve

lash

is

inspected.

NOTICE

The camshafts must be correctly timed with the
crankshaft before an adjustment of the lash for the
fuel injector is made.

Inspect the adjustment of the lash for the fuel injector
according to the Testing and Adjusting, “Fuel Injector
Adjustment”. Adjust the lash for the fuel injector, if

necessary.

i07398052

Fuel

Injector

-

Replace

Fuel leaked or spilled onto hot surfaces or electri-
cal components can cause a fire.

NOTICE

Do not allow dirt to enter the fuel system. Thoroughly
clean the area around a fuel system component that
will be disconnected. Fit a suitable cover over any
disconnected fuel system components.

NOTICE

If a fuel injector is suspected of operating outside of
normal parameters it should be removed by a quali-
fied technician. The suspect fuel injector should be
taken to an authorised agent for inspection.

Refer to the appropriate Disassembly and Assembly
manual for the removal and installation procedure.

i07458937

Fuel

System

-

Prime

If

air

enters

the

fuel

system,

the

air

must

be

purged

from

the

fuel

system

before

the

engine

can

be

started.

Air

can

enter

the

fuel

system

when

the

following

events

occur:

• The fuel day tank is empty or partially drained

• The low-pressure fuel lines are disconnected

• A leak exists in the low-pressure fuel system

• The fuel filter has been replaced

Use the following procedures to remove air from the
fuel system.

70

M0088207

Maintenance Section
Fuel Injector - Inspect/Adjust

«
...
68
69
70
71
72
...
»

Содержание 4006D-E23TA

























































































Отзывы:

Нет отзывов