Perkins 4006D-E23TA Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 88

Perkins 4006D-E23TA Скачать руководство пользователя страница 69

4.

Stop the engine and allow the oil to drain back to

the oil pan for a minimum of 10 minutes.

Illustration 52

g01165836

(Y)

“

Min

”

mark.

(X)

“

Max

”

mark.

5.

Remove the engine oil level gauge (5) to check the

oil level. Maintain the oil level between the

“

MIN

”

and

“

MAX

”

marks on the engine oil level gauge.

i02461963

Engine

Protective

Devices

-

Check

Alarms

and

shutoffs

must

function

properly.

Alarms

provide

timely

warning

to

the

operator.

Shutoffs

help

to

prevent

damage

to

the

engine.

It

is

impossible

to

determine

if

the

engine

protective

devices

are

in

good

working

order

during

normal

operation.

Malfunctions

must

be

simulated

in

order

to

test

the

engine

protective

devices.

A

calibration

check

of

the

engine

protective

devices

will

ensure

that

the

alarms

and

shutoffs

activate

at

the

setpoints.

Ensure

that

the

engine

protective

devices

are

functioning

properly.

NOTICE

During testing, abnormal operating conditions must
be simulated.

The tests must be performed correctly in order to pre-
vent possible damage to the engine.

To prevent damage to the engine, only authorized
service personnel or your Perkins dealer should
perform the tests.

Visual Inspection

Visually check the condition of all gauges, sensors
and wiring. Look for wiring and components that are
loose, broken, or damaged. Damaged wiring or
components should be repaired or replaced
immediately.

i03783789

Engine

Valve

Lash

-

Inspect/

Adjust

(Valves

and

Valve

Bridges)

NOTICE

Only qualified service personel should perform this
maintenance. Refer to the Service Manual or your au-
thorized Perkins dealer or your Perkins distributor for
the complete valve lash adjustment procedure.

Operation of Perkins engines with incorrect valve
lash can reduce engine efficiency, and also reduce
engine component life.

Ensure that the engine cannot be started while
this maintenance is being performed. To help pre-
vent possible injury, do not use the starting motor
to turn the flywheel.

Hot engine components can cause burns. Allow
additional time for the engine to cool before
measuring/adjusting valve lash clearance.

Note: The valve bridges must be equalized before
the valve lash is adjusted.

Refer to Systems Operation, Testing and Adjusting,
“Valve Lash - Adjust” for the correct procedure.

i07395689

Fan

Drive

Pulley

-

Check

(4008-30

Engine

Only)

1.

Isolate

the

electrical

supply

to

the

engine.

M0088207

69

Maintenance Section

Engine Protective Devices - Check

«
...
67
68
69
70
71
...
»

Содержание 4006D-E23TA

























































































Отзывы:

Нет отзывов