manualshive.com logo in svg

Perkins 1106 Series, Руководство пользователя, Страница: 61 / 64

Поделиться
Скачать
Perkins 1106 Series Скачать руководство пользователя страница 61

N40469 

Chapter 8

Page 51

General data

Engine

Number of cylinders.........................................................................................................................................6

Cylinder arrangement ..............................................................................................................................In line

Cycle............................................................................................................................................... Four stroke

Induction system:.....................................................................................................Turbocharged aftercooling

Combustion system ...................................................................................................................Direct injection

Nominal bore ......................................................................................................................... 105 mm (4.13 in)

Stroke .................................................................................................................................... 127 mm (5.00 in)

Compression ratio: ................................................................................................................................. 16.2:1

Cubic capacity .......................................................................................................................6.6 litres (365 in

3

)

Firing order ................................................................................................................................. 1, 5, 3, 6, 4, 2

Valve tip clearances (hot or cold):

- Inlet................................................................................................................................. 0.35 mm (0.0138 in)

- Exhaust .......................................................................................................................... 0.35 mm (0.0138 in)

Lubricating oil pressure (minimum at

maximum engine speed and normal

engine temperature) .............................................................................................................................. 3.6 bar

Capacity of lubricating oil sump:

- Maximum .................................................................................................................... 15.0 litres (3.3 gallons)

Coolant capacity (closed circuit) ....................................................26.3 litres (46.26 UK pints) 27.7 US quarts

Direction of rotation ....................................................................................................Clockwise from the front

Batteries ....................................Two 12 volt 510 amperes (BS3911) or two 12 volt 790 amperes (SAE J537)

Weight of the engine with coolant and engine lubricating oil, M300C, M250C .......................738 kg (1627lbs)

Weight of the engine with coolant and engine lubricating oil, M216C, M190C .......................736 kg (1623lbs)

Содержание 1106 Series

































































Отзывы:

Нет отзывов