manualshive.com logo in svg

Perkins 1106 Series, Руководство пользователя, Страница: 55 / 64

Поделиться
Скачать
Perkins 1106 Series Скачать руководство пользователя страница 55

N40469 

Chapter 5

Page 45

• 

Bent pushrods 

• 

Broken socket on the upper end of a pushrod 

• 

Loose adjustment screw for the valve lash 

If the camshaft and valve lifters show rapid wear, look 

for fuel in the lubrication oil or dirty lubrication oil as a 

possible cause.

• 

Valve Lash Check 

Corrosion

This can occur when two different metals are in 

contact near to, or in, sea water. For example, a brass 

or bronze pipe fitted into aluminium can cause rapid 

corrosion. For this reason, special precautions are 

necessary when an engine is installed. In this situation, 

some components will be connected to a sacrificial 

anode fitted to the hull. Specialist manufacturers will 

advise on the maintenance of these anodes.

Supplementary tools

A general tool kit and an on-board repair kit 

are available from your Perkins Distributor. It is 

recommended that the tools and other parts, listed 

below, are also retained on-board:

Wire, 20 SWG (1mm in diameter) 

Insulation tape 

Jointing compound

Magnet (keep this away from the compass) 

Mechanical fingers

Self-gripping wrench

Suitable lagging material

Rubber olives for the low-pressure fuel system

Extra blades for a small hacksaw

Содержание 1106 Series

































































Отзывы:

Нет отзывов