Performax 241-1395 Скачать руководство пользователя страница 10

 

10 

 
 
 

LED LIGHT 

 
The LED light (1) will illuminate the 
immediate work area (Fig 6). To turn the 
LED light ON, press the LED switch (2) 
once. To turn the LED switch OFF, press 
the LED switch a second time. 
 

NOTE:

 Make sure you turn the LED switch 

OFF when the LED light is not in use to 
prevent the battery from being run down. 
 

PREPARING SCREW HOLES 

 

NOTE

: Use conventional drill bits and drill 

to drill screw holes.

 

  
It is important to prepare screw holes 
before attempting to fasten two pieces of 
wood together. Proper preparation will 
make screws drive easier and prevent 
misaligned components, stripped screw 
heads, splitting and separating of wood 
components.  
 
1.  Clamp components that are to be 

screwed together in their desired 
position (Fig. 7). 
 

2.  Drill a pilot hole (1) through the outer 

piece (2) and into the inner piece (3). 
Drill hole 2/3 the diameter of the 
smooth portion of the screw shank. 
 

NOTE:

 If the wood is soft, drill the hole 2/3 

the length of the screw. If the wood is hard, 
drill the hole the full length of the screw. 
 
3.  Remove the clamp from the two 

pieces to be screwed together. 
 

4.  Enlarge the hole (1) in the outer piece 

(2) so it is the same size as the 
smooth portion of the screw shank 
(Fig. 8). 

 

ASSEMBLY & OPERATION 

 

Fig. 7 

 

 

Fig. 8 

Fig. 6 

 

Содержание 241-1395

















Отзывы: