Performax 240-3605 Скачать руководство пользователя страница 46

Страница: 46 / 48

SYMPTOM

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

Does not make accurate 45°

and 90°

1. Miter gauge out of adjustment

1. Adjust miter gauge

Does not make 45° and 90°

rip cuts.

1. Positive stop not adjusted correctly.

2. Bevel angle pointer not set accurately.

3. Rip fence not properly aligned.

1. Check blade with square and adjust

positive stop.

2. Check blade with square and adjust to

zero.

3. Align the rip fence with the miter gauge

slot.

Material pinched blade when

ripping

1. Rip fence not aligned with blade

2. Warped wood, edge against fence is not

straight

1. Check and adjust rip fence

2. Select another piece of wood

Material binds on riving knife

1. Riving knife not aligned correctly with

blade

1. Check and align riving knife with blade

Saw makes unsatisfactory

cuts

1. Dull blade

2. Blade mounted backwards

3. Gum or pitch on blade

4. Incorrect blade for work being done

5. Gum or pitch on blade causing erratic feed

1. Replace blade

2. Turn the blade around

3. Remove the blade and clean with

turpentine and coarse steel wool

4. Change the blade

5. Clean table with turpentine and steel

wool

Material kicked back from

blade

1. Rip fence out of adjustment

2. Riving knife not aligned with blade

3. Feeding stock without rip fence

4. Riving knife not in place

5. Dull blade

6. The operator letting go of material

before it is past saw blade

7. Miter angle lock knob is not tight

1. Align rip fence with miter gauge slot

2. Align riving knife with blade

3. Install and use rip fence

4. Install and use riving knife (with

guard)

5. Replace blade

6. Push material all the way past saw

blade before releasing work

7. Tighten knob

Blade does not raise or tilt

freely

1. Sawdust and dirt in elevation/tilting

mechanisms

1. Brush or blow out loose dust and dirt

TROUBLESHOOTING

_ 46 _

Содержание 240-3605

















































Результаты поиска

Содержание 240-3605

Отзывы:

Бренды по названию

Популярные бренды

Performax 240-3605, Руководство оператора

Результаты поиска

Содержание 240-3605

Отзывы:

Бренды по названию

Популярные бренды