Performax 240-3605 Скачать руководство пользователя страница 4

Страница: 4 / 48

The purpose of safety symbols is to attract your attention to possible dangers. Please pay careful attention to the safety symbols

and the definition. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give

are no substitutes for proper accident prevention

measures.

WARNING:

Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as

“DANGER,” ”WARNING,”

and

“CAUTION”

before using this tool. Failure to following all instructions listed below may result in

electric shock, fire, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL:

Indicates DANGER, WARNING, OR CAUTION. May be used in conjunction with other

symbols or pictographs.

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

SAVE THESE INSTRUCTIONS!

SAFETY INSTRUCTIONS

_ 4 _

Содержание 240-3605

















































Результаты поиска

Содержание 240-3605

Отзывы:

Бренды по названию

Популярные бренды

Performax 240-3605, Руководство оператора

Результаты поиска

Содержание 240-3605

Отзывы:

Бренды по названию

Популярные бренды