background image

5

CONTROLS AND COMPONENTS

1. Keyless Chuck

2. Chuck Grip
3. Belt Hook
4. Grip
5. Lock on Button
6. Trigger
7. Forward/Reverse Lever

4

6

7

1

3

5

OPERATING THE DRILL

OPERATING THE ON/OFF SWITCH

WARNING: Never tape the trigger switch 

down to provide continuous high speed. 
The tool may fail under such conditions 
causing fire or personal injury.

Squeeze the trigger switch to turn the tool 
“ON”. Release the trigger switch to turn
the tool “OFF”. The amount of pressure put 
on the trigger will vary the speed of the drill. 
Fully pressing the trigger will increase the 

rpms to maximum.

When drilling for extended periods, the 

“Lock-On” switch may be used, but do not
use this switch in situations where the drill 
is likely to bind or kickback. If kickback
does occur, the sudden motion of the tool 

may make it difficult to release the “Lock-

On” switch and turn the drill off.

REVERSING SWITCH LEVER

NOTICE: Be sure the trigger is released 

when changing the position of the lever. 

Always check the direction of the Drill’s 

rotation before use.

The reversing switch lever reverses the
rotation of the drill bit. It is located just
above the trigger switch. ALWAYS turn the

motor off and let the bit come to a
complete stop before moving the switch.
Move the switch to the right for a forward
rotation of the bit. Move the switch to the
left to put the bit into reverse.

CAUTION: Do not change the direction 

of a moving bit. Make sure the bit comes 
to a complete standstill before moving 
switch. Changing direction while the bit is 
moving can cause damage to the drill.

INSTALLING ACCESSORIES

BIT INSERTION
• Unplug the drill. Never change bits on a
live drill.
• Make sure the bit is undamaged,
sharp and free from wood or metal
shavings. Foreign material on the bit may
keep the chuck from tightening fully. A
loose bit may cause injury.
• Push the bit into the chuck as far as it
will go.
• Make sure the bit is in the center of the
chuck. If the bit is off-center, it will not be
held securely and may fly loose during use
causing serious injury.
• Rotate the keyless chuck clockwise until
tight while holding the chuck grip to lock the
bit in place.

 OPERATION

WARNING: Always unplug the tool before changing accessories.

2

Содержание W50086








Отзывы: